Nagyszerű... nagyon csendes...

Ottimo...silenziosissima.....

Nagyszerű... nagyon csendes...

Nagy rajongó, erős, csendes

Great Fan, powerful, quiet

Nagy rajongó, erős, csendes

cikk a leírtak szerint

item as described

cikk a leírtak szerint

Ahogy várható volt. Jó csomagolás, jó minőségű.

As expected. Good packing, good quality.

Ahogy várható volt. Jó csomagolás, jó minőségű.

Fast delivery, items as described. Will be back for more

Fast delivery, items as described. Will be back for more

Fast delivery, items as described. Will be back for more

Fast delivery, itam as described. Pleasure to work with Thanks

Fast delivery, itam as described. Pleasure to work with Thanks

Fast delivery, itam as described. Pleasure to work with Thanks

Ideal for Prusa MK3

Ideal for Prusa MK3

Ideal for Prusa MK3

funktioniert super

funktioniert super

funktioniert super

Jó állapotban szállított anyagok. TOP!

Materials delivered in good condition. TOP!

Jó állapotban szállított anyagok. TOP!

These fans are cheap... I mean... REALLY CHEAP. They are noisy, they rattle, and worst of all the wires break off VERY easily. I highly recommend that before you jostle them at all, you make sure the wires are safely stowed in the cable organizing clips and them use a drop of hot glue to better support the wires. If a wire breaks off while unpacking... peel back the sticker and attempt to solder it back on. Be extremely careful as the wires from the fan are run directly to the board and heating the solder pad to repair it can cause the other wire to fall off. Use as low of a temperature as possible to solder this joint (start at 200 c and work up from there). If you use too high a heat, the wire breaks and it's toast. As for the performance... just WOW... I've had terrible problems 3d printing with these fans in the beginning because no matter how much power I feed the heating elements of the printer, these fans are actually causing at least a 5-10 degree drop in temperature. I've had to cut back to 80% speed to print reliably. The noise level of these fans becomes tolerable at about 75% speed.

These fans are cheap... I mean... REALLY CHEAP. They are noisy, they rattle, and worst of all the wires break off VERY easily. I highly recommend that before you jostle them at all, you make sure the wires are safely stowed in the cable organizing clips and them use a drop of hot glue to better support the wires. If a wire breaks off while unpacking... peel back the sticker and attempt to solder it back on. Be extremely careful as the wires from the fan are run directly to the board and heating the solder pad to repair it can cause the other wire to fall off. Use as low of a temperature as possible to solder this joint (start at 200 c and work up from there). If you use too high a heat, the wire breaks and it's toast. As for the performance... just WOW... I've had terrible problems 3d printing with these fans in the beginning because no matter how much power I feed the heating elements of the printer, these fans are actually causing at least a 5-10 degree drop in temperature. I've had to cut back to 80% speed to print reliably. The noise level of these fans becomes tolerable at about 75% speed.

These fans are cheap... I mean... REALLY CHEAP. They are noisy, they rattle, and worst of all the wires break off VERY easily. I highly recommend that before you jostle them at all, you make sure the wires are safely stowed in the cable organizing clips and them use a drop of hot glue to better support the wires. If a wire breaks off while unpacking... peel back the sticker and attempt to solder it back on. Be extremely careful as the wires from the fan are run directly to the board and heating the solder pad to repair it can cause the other wire to fall off. Use as low of a temperature as possible to solder this joint (start at 200 c and work up from there). If you use too high a heat, the wire breaks and it's toast. As for the performance... just WOW... I've had terrible problems 3d printing with these fans in the beginning because no matter how much power I feed the heating elements of the printer, these fans are actually causing at least a 5-10 degree drop in temperature. I've had to cut back to 80% speed to print reliably. The noise level of these fans becomes tolerable at about 75% speed.