Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (207)
  • Kép (21)
  • Videó (2)
  • Minden csillag
    • Minden csillag(207)
    • 5 Csillag(183)
    • 4 Csillag(10)
    • 3 Csillag(8)
    • 2 Csillag(2)
    • 1 Csillag(4)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 16/09/2017

    It seems that there´s a huge mistake maken in the description. Voltage Output for Safety Switches on MY Anet A8 is 5V. This sensor, however, needs 10-30V´s working Voltage...The led also stays dark, which is very useless for configuration. It´s kinda bad that my printer arrived about 1month later, so now i can´t return it back. People be aware and measure the output Voltage on the S_Z-Port on your A8-Mainboard!!

    Hozzászólások
    Mutasd az eredetit
  • 02/09/2017

    Leider nicht so 100 Prozentig. Um die Montage zu erleichtern wird eine Leiste mit zwei Schrauben auf der Rückseite befestigt, sie sollen die Gewindemutter für den Geber fixieren, leider ist die Schlüsselweite von 6mm zu groß für die Mutter (SW 5,5) beim festziehen der Schrauben kann recht schnell die Mutter durchdrehen. Die Schrauben von der Leiste sind von der Geberseite montiert, welches zur Folge haben kann das sie nicht an der Führungskassette vorbei kommen, Abhilfe die Schrauben von der Rückseite durch stecken und den Kopf versenken. Ich finde diese Lösung etwas halbherzig, schöner Schriftzug (leider nur von der Rückseite lesbar), aber nicht mal Unterlegscheiben.

    Hozzászólások
    Mutasd az eredetit
  • 28/07/2021

    Mit is mondhatnék erről? A kábel és a csatlakozó jó minőségű, meg kellett fordítani a színeket, visszapattant tökéletesen után szétszerelés. Legyen óvatos a tartó biztosított automatikus szint érzékelő, nagyon törékeny. Eltört, amikor felhúztam. A tartó és a nyakkendő a mosfethez készült. A csomagban 3 ferrules található, amelyeket extraként használhat

    Hozzászólások
    Mutasd az eredetit
  • 02/09/2019

    recebido hoje dia 02-09-2019, embalado saco plástico, aparentemente perfeito sem nenhum problema, ainda não não testei.

    Hozzászólások
    Mutasd az eredetit
  • 01/04/2019

    Tudo certo

    Hozzászólások
    Mutasd az eredetit
  • 14/02/2019

    The sensor was delivered to me. In testing I found it does not work with the original firmware on ANET. You need to use MARLIN or SKYNET 3D. So I can not write whether it is operational. When I change the firmware I test the sensor. Nevertheless, 5 stars.

    Hozzászólások
    Mutasd az eredetit
  • 07/02/2019

    Produto excelente.

    Hozzászólások
    Mutasd az eredetit
  • 22/09/2017

    La pieza se ve de buena calidad y probablemente funcione muy bien sin embargo se les ocurrio embalar juntos en un solo empaque varios articulos uno de los cuales pesa mas de 300 gramos y es completamente metalico y pues este articulo tiene una base de acrilico asi que no soporto y llego fracturada en 3 piezas... Espero puedan dar una solucion para este problema.

    Hozzászólások
    Mutasd az eredetit
  • 09/07/2017

    quality auto-leveling sensor with holder. Anet original. instructions to attach and use it are found on YouTube very easy to do it.

    Hozzászólások
    Mutasd az eredetit
  • 31/08/2017

    Complicated setup, but works well once this is done. Be careful, though, as there is no support behind the screws which hold it in place, and the acrylic backplate cracks very easily if the screws are overtightened. A piece of 5mm material beteen the bearings will give support where needed.

    Hozzászólások (1)
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    recommendation for you
    • US$24.99
    • US$49.99
    • US$2.71
    • US$19.62
    • US$15.00
    • US$64.99
    • US$10.49
    • US$8.99
    • US$34.99
    • US$6.89
    • US$145.00
    • US$289.00
    • US$4.61
    • US$10.38
    • US$19.99
    • US$64.99
    • US$29.99