Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (244)
  • Kép (65)
  • Videó (1)
  • Minden csillag
    • Minden csillag(244)
    • 5 Csillag(214)
    • 4 Csillag(24)
    • 3 Csillag(5)
    • 2 Csillag(0)
    • 1 Csillag(1)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 09/08/2020

    Shipping took 3 work-days and the printer came partly assembled and nicely packaged. The printer has a steel sheet-metal frame with some magenta-metallic aluminum parts and some 2020/2040 aluminum V-Slot profiles. Stiff coupler for the z-Motor and ferrules! The frame is reasonable stiff for a printer and the assembly was easy thanks to the great pdf-manual on a SD-Card and the video on the Biqu-youtubechannel. Every bag of screws is labeled and you also get some spares as well as any tool or wrench you need. The Cablemanagement is great and you are supplied with enough cableties. The type-C cable makes maintanance on the hotend easy and you dont have to deal with multiple cables at all. My bowden was a little short and was bending a bit much, 5cm longer would solve this. The hotend is a grub screw clamped V6 hotend 0.4mm nozzle and two spares. The heatbed is a 3mm aluminum-PCB with a magnetic pad and a springsteelsheet. It works very well and heats up to 250°/80° in 5-7 min. Unfortunately my bed is not flat, so at some point I will have to buy a BL-Touch for autoleveling to compensate that. The TMC-Driver make this printer as silent as a Prusa but this is mitigated by the case and driver-cooling fans which are as loud(48dB@1m) as a hairdryer on lowest level. You cant tell if the printer is running or not! These must be replaced if you consider printing in a livingroom. Touchscreen is bright, responsive and has many configuration options. I also had to adjust the steps-per-mm-value of x and y from 81.5 to 80.00 to get my parts to nearly the correct size. I dont understand why they choose these values in the first place since 80.00 is the calculated standard value for this assembly. The printquality is very good and bed adhesion is fantastic. All in all this printer is a very good deal, but it has some flaws which should be fixed or adressed. Its maybe not the best for a total beginner, but with a little bit of finetuning you could turn this into a great printer.

    Hozzászólások (1)
    Mutasd az eredetit
  • 29/07/2021

    Öt csillag, szenzációs! Könnyen összeszerelhető, és a kézikönyv nagyon magyarázó, alig kell olvasni. A darabok meg vannak számozva, és a szerszámok összeszerelésre készülnek. Egy szoftver kérdésében, a benne telepített szoftver nagyon jó. Gyakorlatilag összeszerelik és otthagyják a nyomtatást. Természetesen egy kezdő számára némi tanulást igényel, de sikerült kinyomtatnom a kedvenc darabomat, amint befejeztem a összeállítást. Igazán szenzációs! A különbség a led megvilágítja a nyomtatóágyat. Csak egy részlet hiányzott, az a memóriakártya, ami nem jutott eszembe. Én is nagyon elégedett vagyok a viteldíj biztosításával. A vámdíj teljes összegével váltottam meg, és nagyon gyors volt. A személyzet nagyon jól kitartott mellettem!

    Hozzászólások (2)
    Mutasd az eredetit
  • 19/07/2020

    OK the printer isnt all bad but in its current state is certainly not for first time buyers. So far I have replaced a pulley that squeaked because it was rubbing against a metal spacer, the USB port does not line up with the whole in the case so cannot use until i widen the hole. It has no bed wire strain relief which we had to find and adapt to this printer as it is vital. This is all in a single day, we fix an issue and find another. Most of these are pretty minor but no one buys a printer to have to fix its issues. I think a selection should have been sent out to enthusiasts to test and give feedback, ive seen a single review and that was after its release. On the flip side there is a lot i do love about this printer, the colour is funky, the extruder is metal, the touchscreen and software seems sound and it has potential. I just dont think its quite there on the testing and tweaking part before it should have been released.

    Hozzászólások (1)
    Mutasd az eredetit
  • 08/07/2021

    Jól csomagolva jött, de sajnos nem jött az SD kártyával, 50 gramm PLA-val jön, amit egy kis, könnyű összeszereléssel lehet játszani, és már nagyon jó minőségű nyomtatással van ellátva a dobozból, Nem kellett mást tennem, csak az asztal beállítását, hogy kiváló minőségű ujjlenyomatot kapjak. Javasolná kezdőknek.

    Hozzászólások (6)
    Mutasd az eredetit
  • 03/02/2021

    nice 3d printer . good quality . dont expect to make job with the 50 gr of filament that the printer include . i assembled it with the help of a video in you tube . i recomend it. good print quality

    Hozzászólások
    Mutasd az eredetit
  • 08/08/2020

    I own many 3d printer but for sure this is the best one . high quality materials. biqu have put a lot of effort on this product. I recommend 100% . biqu have the best customer service. great results with pla and petg . going to order another soon for my farm

    Hozzászólások
    Mutasd az eredetit
  • 15/07/2020

    Lieferung innerhalb von 48 Stunden 👍😍 Drucker läuft sehr gut und das Display mit Software ist fantastisch. sehr viele Einstellungen möglich. Ist nicht mein erster Drucker aber der Drucker ist für diesen Preis mit 32 Bit Board das Geld Wert. würde diesen immer wieder Kaufen.

    Hozzászólások (3)
    Mutasd az eredetit
  • 06/09/2021

    Nagyon jó nyomtató az ár, és megérkezett a becsült szállítási dátum. Az én országomban adót és elszámolási díjakat számoltam fel, de mivel volt tarrif biztosításom, a bumm-jó 100%-os visszatérítést nyújtott. 5 csillag a termék és a szolgáltatás. Az egyetlen hátránya az volt, hogy a nyomtatóm megsérült a szállítás közben, ez az Amarex hibája, de a nyomtató még mindig 100%-ban működik

    Hozzászólások
    Mutasd az eredetit
  • 18/07/2021

    Nem tudom leírni a nyomtatót. Egyszerűen elbűvölt. Ez egy biztos és nagyon boldog választás volt. Erősen ajánlom, hogy megvásárolja ezt a nyomtatót!!!

    Hozzászólások (2)
    Mutasd az eredetit
  • 03/01/2021

    szuper jól csomagolt, sok jó minőségű hab, a nyomtató nagyon könnyen szerelhető és a doboz minősége jó, miután néhány frissítés már szinte tökéletes

    Hozzászólások (2)
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    Lehet, hogy érdekli

    recommendation for you
    • US$8.99
    • US$34.99
    • US$6.89
    • US$145.00
    • US$199.00
    • US$289.00
    • US$4.61
    • US$282.00
    • US$11.54
    • US$449.00