Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (35)
  • Kép (2)
  • Videó (0)
  • Minden csillag
    • Minden csillag(35)
    • 5 Csillag(32)
    • 4 Csillag(2)
    • 3 Csillag(1)
    • 2 Csillag(0)
    • 1 Csillag(0)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 17/12/2020

    Everything came perfect, cant wait to install

    Hozzászólások
    Mutasd az eredetit
  • 03/10/2020

    product arrived quick and on time. but as soon as I plugged it in to the motherboard correctly it started letting out the magic smoke. upon closer inspection 4 of the wires were the wrong way round from the factory. I had to swap the black and white around for the end stop signal and also the more important one was the 5v positive (red) and the ground (blue) which were also the wrong way round. I'm so lucky it didn't fry my board. the only wire in the right place was the yellow signal wire. it would have been better if the connections on the other end were all separate Dupont style single connections that way you can swap them around as you please. apart from that it's working fine now and am happy with the product 👍🏻

    Hozzászólások (3)
    Mutasd az eredetit
  • 27/02/2021

    Good unit, well packed. Be very careful with the cable colours and pin orders: some colours are different from AntClabs documentation, and the colours that are the same are at different positions! On my Ender 3 V2, I had to permute almost all wires! You shoud double and triple check! The provided bracket does not fit the Ender 3 V2, just print the right one from Thingiverse. The cable was long enough for the Ender 3 V2, with a bit extra. I followed the very good Ender 3 V2 BLTouch installation video on "Teaching Tech" Youtube channel (except for cable colours, of course!). I used his suggested wiring with no issue (i.e. connecting the contact signal in place of the Z axis home switch, and of course I had to permute the white and black wires!) At first I didn't realize that the Z axis would crush the Z home switch and this would prevent proper leveling. I simply removed the Z switch and its bracket; it is replaced by the BLTouch anyway. Dr Vax has a good video on his channel as well, with a different wiring on the E3V2 (all 5 pins connected to the "BLtouch" connector). I didn't try this wiring, though. One installed, works like a charm! I get very consistent first layer even when switching from Glass Bed to PEI Steel sheet. One star removed because the pinout is not exactly easy to find and the wire colours don't match the documentation I could find.

    Hozzászólások
    Mutasd az eredetit
  • 09/09/2021

    ..

    Hozzászólások
    Mutasd az eredetit
  • 18/03/2021

    takarít meg annyi erőfeszítést ágy szintező, nem triviális, hogy a szoftver frissített, bár így megragad egy pár sört!

    Hozzászólások
    Mutasd az eredetit
  • 19/11/2021

    Hozzászólások
    Mutasd az eredetit
  • 19/10/2021

    Rendben

    Hozzászólások
    Mutasd az eredetit
  • 27/05/2021

    Very excellent, high quality and fast shipping

    Hozzászólások
    Mutasd az eredetit
  • 16/04/2021

    Looks perfect but haven't tested yet.

    Hozzászólások
    Mutasd az eredetit
  • 26/03/2021

    very good

    Hozzászólások
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    Lehet, hogy érdekli

    recommendation for you
    • US$3.45
    • US$10.38
    • US$11.54
    • US$33.48
    • US$12.71
    • US$11.54
    • US$5.76
    • US$4.61
    • US$11.54
    • US$5.97
    • US$10.99
    • US$46.19
    • US$5.76
    • US$6.99
    • US$5.76
    • US$1.50
    • US$49.65
    • US$103.49