Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (647)
  • Kép (72)
  • Videó (0)
  • Minden csillag
    • Minden csillag(647)
    • 5 Csillag(614)
    • 4 Csillag(27)
    • 3 Csillag(3)
    • 2 Csillag(0)
    • 1 Csillag(3)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 13/02/2020

    Highly recommended. Instructions are a bit brief, but sufficient. With my Ender 3 Pro w/ upgraded Creality 1.1.5 silent mainboard I had none of the issues described by the TeachingTech tutorial. I received a genuine BLTouch V3.1, and also had none of the “BLTouch V3 incompatibility w/ Ender 3”-problems. Creality had stepped up to the plate after all the complaints about crappy software.

    Hozzászólások (3)
    Mutasd az eredetit
  • 11/04/2019

    Works well on Ender 3, BUT if your control board has capacitor C7 installed (see photo) then you must remove it, or the very short duration Z-stop signal from BLTouch will not be detected and the extruder will just crash into the print bed when it auto-homes. This is a known issue with BLTouch and the latest Ender 3 control boards leave out C7. To refit the Ender 3/Pro cover and fan, you need to bend the four pins on the adapter PCB so that the 4-way header from BLTouch is horizontal. Versions of this kit sold elsewhere have the pins already bent.

    Hozzászólások
    Mutasd az eredetit
  • 17/07/2020

    Works a charm. Requires a little work to set up, but following instructions its all fairly straightforward. Instructions are not great, but there are plenty of excellent videos online (I suggest the "Teaching Tech" channel). It is very easy to accidentally insert one of the connectors incorrectly (one column of pins over). I did this and had issues, thought it was the firmware upload and went through various firmware revisions before finding the mistake. I downloaded the latest firmware and set up according to online instructions. Now my first layer goes down a treat *every single time* without the need to check the bed levelling manually with paper. I cannot recommend this product more strongly - I'm kicking myself for not ordering the printer with this option pre-installed. If you don't have an automatic bed leveller - this is the number one upgrade to buy before anything else.

    Hozzászólások
    Mutasd az eredetit
  • 24/08/2020

    This works great! No more spinning the wheels over and over again to level my bed before 3-D printing. The install is a little bit tricky but there are lots of online instructions and videos to help you. highly recommended.

    Hozzászólások
    Mutasd az eredetit
  • 04/11/2019

    Works great on original CR-10 (V1). I did struggle with flashing, so use official website with latest version. https://www.creality.com/download/bl-touch-firmware_c0006 I had great results with flash: latest CR-101.1.6BLTouchV3.1PowerLossContinueEnglish.hex Just make sure sure that fuse settigs are D6, DC, FD (as described in manual) Also, do not that you will have to remove z-limiter wiring, and do manual z-offeset settings..

    Hozzászólások
    Mutasd az eredetit
  • 04/09/2019

    Kit for the ender 3 with all that you need to install it. nice box. The product complies as described in the add. I received V3.1

    Hozzászólások
    Mutasd az eredetit
  • 03/05/2020

    Ez a megfelelő készlet az Ender 3.-hoz Tartalmazza a BLT-et és a rögzítő konzolt és a kábeleket. A vezérlőpult villogásához szükséges készletet is tartalmazza. Az enyém a BLT-V3.1-es verzióval jött.

    Hozzászólások
    Mutasd az eredetit
  • 10/01/2021

    Semma product buyed from Tamilnadu, chennai. It tooks 2months to arrive in corona period.

    Hozzászólások
    Mutasd az eredetit
  • 14/09/2020

    This product arrived within 2 weeks of ordering it. For international delivery I am very impressed. The item itself is really well packaged. It is complete, and appears to be of good quality. My printer is currently mid print so I have not had a chance to install it, but as this is a genuine item I have no doubts it will function perfectly.

    Hozzászólások
    Mutasd az eredetit
  • 03/07/2020

    A Creity V1-es alaplaphoz BL-t vettem. Viszonylag könnyen telepíthető (Ender 3), ha egyszer telepítve és engedélyezve van a szoftverben, úgy működik, ahogy az várható volt. Ennek a megoldásnak az egyetlen hátránya, hogy a Pinboard A (tű bővítő BL-hez) nem igazán illeszkedik az alaplap burkolatába, ha az összes kábelhez csatlakozik, mivel túl magas és ütközik a ventillátorral. Azt is érdemes megjegyezni, hogy adjunk automatikus szintező parancsokat a szeletelő kimeneti kód.

    Hozzászólások
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    Lehet, hogy érdekli

    recommendation for you
    • US$2.71
    • US$9.99
    • US$6.92
    • US$6.89
    • US$13.79
    • US$8.07
    • US$9.99
    • US$7.35
    • US$4.99
    • US$8.99
    • US$34.99
    • US$6.89
    • US$4.61
    • US$289.00
    • US$145.00
    • US$10.38
    • US$29.00
    • US$6.92