Eachine Beecore F3_EVO_Brushed Repülési Ellenőrző Tábla Inductrix Tiny Whoop Eachine E010 E010S-hez vélemények - Banggood Magyar online vásárlás

Eachine Beecore F3_EVO_Brushed Repülési Ellenőrző Tábla Inductrix Tiny Whoop Eachine E010 E010S-hez

30,89€
~~32,28€~~
Vásárolj most

Vásárlói vélemények

4.88 / 5

Az összes 758 vélemény megtekintése

5 csillag
697 (92.0%)
4 csillag
40 (5.3%)
3 csillag
12 (1.6%)
2 csillag
6 (0.8%)
1 csillag
3 (0.4%)

Írja meg a véleményét Szerezzen dupla értékelési pontot, ha Ön az első 3 közzétett értékelés egyike!

Minden vélemény (758)
Kép (97)
Videó (21)
Minden csillag
- Minden csillag(758)
- 5 Csillag(697)
- 4 Csillag(40)
- 3 Csillag(12)
- 2 Csillag(6)
- 1 Csillag(3)

Sorrend:

Legjobb áttekintés

Legjobb áttekintés
Leghasznosabb
Legfrissebb

Csak az Ön országából származó vélemények (Hungary)

|

Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

AaronVIP1
US
19/01/2017

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!

I thought I might have to return it after a day of frustration, but after doing some research and persistence I was finally successful. For those who have the FlySky FS-I6 AFHDS 2A transmitters, follow the PDF instructions provided on this site until you get to step "3. Binding Procedure" a) On my FS-I6 it shows AFHDS 2A (On/Off). I selected "Off", which I assume selects AFHDS, and not AFHDS 2A. b) Then follow the rest of the procedures and your transmitter will show "RxBinding" as you power it on with the binding jumpers connected. Watch the flashing green LEDs on the board. When it shows solid green, you are now successful, even though your transmitter still displays "RxBinding". Power off your receiver and beecore, and when you power them up again, you should be good to go!
48

Hozzászólások (4)

Mutasd az eredetit
igyigyVIP1
US
17/11/2016

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight

From the CLI dump, this is the version info # version # Cleanflight/SPRACINGF3EVO 1.13.0 Jun 6 2016 / 00:03:29 (a77bc76) I have yet to solder power and fly it. Will be flashing betaflight
18

Hozzászólások (2)

Mutasd az eredetit

Show:

Teljes 0 oldalakat

Menj az oldalra

Megy

Lehet, hogy érdekli

recommendation for you