Package is full, but the instruction document is not the good one for the colorful led version. I upload a picture with the correct resistor value !

Package is full, but the instruction document is not the good one for the colorful led version. I upload a picture with the correct resistor value !

Package is full, but the instruction document is not the good one for the colorful led version. I upload a picture with the correct resistor value !

All components included easy to solder, good for beginners bcps are labeled for most components 10k (r1,r3,r5 = brn,blk,org,gold) resistors, transistors, capacitors, switch and power connectors are clearly marked 2.2k (red,red,red,gold) goes in r7 on pcb 'A' all others resistors are the 1k (r2, r4, r6 = brn,blk,red,gold) the r7 2.2k resistor runs the top led my kit included one extra led, and had one bad led tree stands 5.5x2.5x2.5 when completed very low power draw, 0.05a

All components included easy to solder, good for beginners bcps are labeled for most components 10k (r1,r3,r5 = brn,blk,org,gold) resistors, transistors, capacitors, switch and power connectors are clearly marked 2.2k (red,red,red,gold) goes in r7 on pcb 'A' all others resistors are the 1k (r2, r4, r6 = brn,blk,red,gold) the r7 2.2k resistor runs the top led my kit included one extra led, and had one bad led tree stands 5.5x2.5x2.5 when completed very low power draw, 0.05a

All components included easy to solder, good for beginners bcps are labeled for most components 10k (r1,r3,r5 = brn,blk,org,gold) resistors, transistors, capacitors, switch and power connectors are clearly marked 2.2k (red,red,red,gold) goes in r7 on pcb 'A' all others resistors are the 1k (r2, r4, r6 = brn,blk,red,gold) the r7 2.2k resistor runs the top led my kit included one extra led, and had one bad led tree stands 5.5x2.5x2.5 when completed very low power draw, 0.05a

Fine kit. Everything was in the package (I even got one extra LED) Instructions are fine, but the delivered resistors does not match the instructions. Just follow the instructions, and use correct resistors (see below)) The correct resistors: R1, R3, R5, R7: 10 kOhm (Note: R7 is only on board CTR-30A) R2: 2,2 kOhm R4: 1 KOhm R6: 33 Ohm (39 Ohm works fine) Have fun.

Fine kit. Everything was in the package (I even got one extra LED) Instructions are fine, but the delivered resistors does not match the instructions. Just follow the instructions, and use correct resistors (see below)) The correct resistors: R1, R3, R5, R7: 10 kOhm (Note: R7 is only on board CTR-30A) R2: 2,2 kOhm R4: 1 KOhm R6: 33 Ohm (39 Ohm works fine) Have fun.

Fine kit. Everything was in the package (I even got one extra LED) Instructions are fine, but the delivered resistors does not match the instructions. Just follow the instructions, and use correct resistors (see below)) The correct resistors: R1, R3, R5, R7: 10 kOhm (Note: R7 is only on board CTR-30A) R2: 2,2 kOhm R4: 1 KOhm R6: 33 Ohm (39 Ohm works fine) Have fun.

Having no experience of electrical circuits I was unsure what to do when this arrived. The download instructions aren't that clear so here are my tips for assembling the multi colour LED version with white LEDs: View a PDF with assembly details here (Credit to the reviewer pages back who posted this): http://www.haoyuelectronics.com/Attachment/CTR-30C/CTR-30C%20Flashing%20Christmas%20Tree%20Instruction.pdf Link with images is: http://www.haoyuelectronics.com/Attachment/CTR-30C/ CTR-30A is one tree PCB CTR-30B is the other one CTR-30C is the base Resistors: These can be fitted in either direction and are: 6 x 1k: Colour bands Gold/Red/Black/Brown 6 x 10k: Colour Bands Gold/Orange/Black/Brown 1 x 2.2k: Colour Band Gold/Red/Red/Red Locate where these go via the pdf and insert in to the relevant location R1, R2 etc... The single 2.2k goes on R7 on CTR-30A. Transistor (With the 3 legs) Must be fitted the right way but the PCB shows the orientation. All are the same spec so use any of them. Capacitor Must be fitted the right way. Longer leg is (+) Positive. And negative side is printed on the casing. All the same spec so fit where required. LEDs Must be fitted the right way. Longer leg is (+). Positive terminal is the lower location where the letter is such as D1, D2 etc. Solder in place with enough length to bend to point out the way. Solder the tree segments together. When you fit the soldered tree to the base I recommend installing and power up to test before soldering in as you can have a (+) against a (+) as per the instructions but it can still be 90 degrees out. I did this and it was a pain to unsolder as I didn't have a solder sucker. It all went together and worked great once I had realigned the tree to the base and works great off USB power.

Having no experience of electrical circuits I was unsure what to do when this arrived. The download instructions aren't that clear so here are my tips for assembling the multi colour LED version with white LEDs: View a PDF with assembly details here (Credit to the reviewer pages back who posted this): http://www.haoyuelectronics.com/Attachment/CTR-30C/CTR-30C%20Flashing%20Christmas%20Tree%20Instruction.pdf Link with images is: http://www.haoyuelectronics.com/Attachment/CTR-30C/ CTR-30A is one tree PCB CTR-30B is the other one CTR-30C is the base Resistors: These can be fitted in either direction and are: 6 x 1k: Colour bands Gold/Red/Black/Brown 6 x 10k: Colour Bands Gold/Orange/Black/Brown 1 x 2.2k: Colour Band Gold/Red/Red/Red Locate where these go via the pdf and insert in to the relevant location R1, R2 etc... The single 2.2k goes on R7 on CTR-30A. Transistor (With the 3 legs) Must be fitted the right way but the PCB shows the orientation. All are the same spec so use any of them. Capacitor Must be fitted the right way. Longer leg is (+) Positive. And negative side is printed on the casing. All the same spec so fit where required. LEDs Must be fitted the right way. Longer leg is (+). Positive terminal is the lower location where the letter is such as D1, D2 etc. Solder in place with enough length to bend to point out the way. Solder the tree segments together. When you fit the soldered tree to the base I recommend installing and power up to test before soldering in as you can have a (+) against a (+) as per the instructions but it can still be 90 degrees out. I did this and it was a pain to unsolder as I didn't have a solder sucker. It all went together and worked great once I had realigned the tree to the base and works great off USB power.

Having no experience of electrical circuits I was unsure what to do when this arrived. The download instructions aren't that clear so here are my tips for assembling the multi colour LED version with white LEDs: View a PDF with assembly details here (Credit to the reviewer pages back who posted this): http://www.haoyuelectronics.com/Attachment/CTR-30C/CTR-30C%20Flashing%20Christmas%20Tree%20Instruction.pdf Link with images is: http://www.haoyuelectronics.com/Attachment/CTR-30C/ CTR-30A is one tree PCB CTR-30B is the other one CTR-30C is the base Resistors: These can be fitted in either direction and are: 6 x 1k: Colour bands Gold/Red/Black/Brown 6 x 10k: Colour Bands Gold/Orange/Black/Brown 1 x 2.2k: Colour Band Gold/Red/Red/Red Locate where these go via the pdf and insert in to the relevant location R1, R2 etc... The single 2.2k goes on R7 on CTR-30A. Transistor (With the 3 legs) Must be fitted the right way but the PCB shows the orientation. All are the same spec so use any of them. Capacitor Must be fitted the right way. Longer leg is (+) Positive. And negative side is printed on the casing. All the same spec so fit where required. LEDs Must be fitted the right way. Longer leg is (+). Positive terminal is the lower location where the letter is such as D1, D2 etc. Solder in place with enough length to bend to point out the way. Solder the tree segments together. When you fit the soldered tree to the base I recommend installing and power up to test before soldering in as you can have a (+) against a (+) as per the instructions but it can still be 90 degrees out. I did this and it was a pain to unsolder as I didn't have a solder sucker. It all went together and worked great once I had realigned the tree to the base and works great off USB power.

This is so beautiful, and quite easy to make. But there's no manual written on paper, and the downloaded manual from the link is not correct.(there was some not included resistors on the manual) So if you make this, solder resistors like this : part A R1=10k R2=1k R3=10k R4=1k R5=10k R6=1k R7=2.2k part B R1=10K R2=1k R3=10k R4=1k R5=10k R6=1k

This is so beautiful, and quite easy to make. But there's no manual written on paper, and the downloaded manual from the link is not correct.(there was some not included resistors on the manual) So if you make this, solder resistors like this : part A R1=10k R2=1k R3=10k R4=1k R5=10k R6=1k R7=2.2k part B R1=10K R2=1k R3=10k R4=1k R5=10k R6=1k

This is so beautiful, and quite easy to make. But there's no manual written on paper, and the downloaded manual from the link is not correct.(there was some not included resistors on the manual) So if you make this, solder resistors like this : part A R1=10k R2=1k R3=10k R4=1k R5=10k R6=1k R7=2.2k part B R1=10K R2=1k R3=10k R4=1k R5=10k R6=1k

I have now purchased 5 of these kits. Lots of fun, once you figure out which resistors go where - See pictures. Youtube has some good videos on construction

I have now purchased 5 of these kits. Lots of fun, once you figure out which resistors go where - See pictures. Youtube has some good videos on construction

I have now purchased 5 of these kits. Lots of fun, once you figure out which resistors go where - See pictures. Youtube has some good videos on construction

Vor kurzem habe ich den Bausatzsatz erhalten und, nachdem ich eine Bauteiliste entsprechend der gelieferten Bauteile im Internet gefunden habe, zusamen gebaut. Nach dem Zusammenbau und dem harten Test, habe ich ein paar Bilder gemacht. Ausserdem habe die Bauteilliste beigelegt. Viel Spass beim Löten.

Vor kurzem habe ich den Bausatzsatz erhalten und, nachdem ich eine Bauteiliste entsprechend der gelieferten Bauteile im Internet gefunden habe, zusamen gebaut. Nach dem Zusammenbau und dem harten Test, habe ich ein paar Bilder gemacht. Ausserdem habe die Bauteilliste beigelegt. Viel Spass beim Löten.

Vor kurzem habe ich den Bausatzsatz erhalten und, nachdem ich eine Bauteiliste entsprechend der gelieferten Bauteile im Internet gefunden habe, zusamen gebaut. Nach dem Zusammenbau und dem harten Test, habe ich ein paar Bilder gemacht. Ausserdem habe die Bauteilliste beigelegt. Viel Spass beim Löten.

Szép fejadag-kiképzési készlet. A nyomtatott áramköri lapok minősége magas: a pályák sima repedések nélkül, a lyukak fémezettek. Könnyen megy, az internet szöveges és videó útmutatók. Az összeszerelt kialakítás egyszerre vált működőképessé mind USB kábellel, mind három AA akkumulátorral. Történetesen van egy készletem, amelyben minden LED három színben világítja meg a поочерёдно-t: piros, zöld és kék. Négy nyílás van az állványon, amit az alaphoz kell rögzíteni, szóval a jövőben talán csinálok egy átlátszó védődobozt ennek a fának. Azt is hozzá kell tenni, hogy ez a design egy nagyon alacsony áramfogyasztás körülbelül 16 mA. Nagy újévi ajándék. Javaslom.

Хороший набор для обучения пайке. Качество печатных плат высокое: дорожки ровные без трещин, отверстия металлизированы. Собирается достаточно легко, в интернете есть текстовые и видео руководства. Собранная конструкция заработала сразу как при питании по USB кабелю, так и от трёх аккумуляторов АА. У меня оказался набор, в котором каждый светодиод светит поочерёдно тремя цветами: красным, зелёным и синим. В подставке есть четыре отверстия для крепления к основе, так что в будущем, возможно, я изготовлю защитный прозрачный корпус для этой ёлки. Ещё нужно добавить, что у этой конструкции очень маленькое потребление тока около 16 мА. Отличный подарок к Новому Году. Рекомендую.

Szép fejadag-kiképzési készlet. A nyomtatott áramköri lapok minősége magas: a pályák sima repedések nélkül, a lyukak fémezettek. Könnyen megy, az internet szöveges és videó útmutatók. Az összeszerelt kialakítás egyszerre vált működőképessé mind USB kábellel, mind három AA akkumulátorral. Történetesen van egy készletem, amelyben minden LED három színben világítja meg a поочерёдно-t: piros, zöld és kék. Négy nyílás van az állványon, amit az alaphoz kell rögzíteni, szóval a jövőben talán csinálok egy átlátszó védődobozt ennek a fának. Azt is hozzá kell tenni, hogy ez a design egy nagyon alacsony áramfogyasztás körülbelül 16 mA. Nagy újévi ajándék. Javaslom.

I have purchase 16 units in total as Xmas gift and everybody LOVE it.

I have purchase 16 units in total as Xmas gift and everybody LOVE it.

I have purchase 16 units in total as Xmas gift and everybody LOVE it.

Funny Christmas toy.

Funny Christmas toy.

Funny Christmas toy.