I am very satisfied. It is a very smart and usefull device. A good product for my money.

I am very satisfied. It is a very smart and usefull device. A good product for my money.

I am very satisfied. It is a very smart and usefull device. A good product for my money.

beklediğimden daha kaliteli çıktı, 1 haftada elime ulaştı

beklediğimden daha kaliteli çıktı, 1 haftada elime ulaştı

beklediğimden daha kaliteli çıktı, 1 haftada elime ulaştı

Excelent

Excelent

Excelent

Két héten belül megkaptam a terméket. Nem használtam részletesebben, de úgy tűnik, működik.

2 Haftada içerisinde ürün elime ulaştı. Daha detaylı bir şekilde kullanmadım ama iş görür gibi duruyor.

Két héten belül megkaptam a terméket. Nem használtam részletesebben, de úgy tűnik, működik.

Great value for the price. Evan the latest software are acceptable.

Great value for the price. Evan the latest software are acceptable.

Great value for the price. Evan the latest software are acceptable.

Telepítse a DRÁVS-t a Hantek.com-ról, nem CD-ről. A sofőr telepítése gyors volt, de sikerült működésre bírnom. Meg kell gomb / kapcsoló mellett USB port oszcilloszkóp H pozícióban (P pozíció logikai csatornák). Ha problémája van a telepítőprogrammal, amely szerint az illesztőprogram nincs aláírva, menjen a következő oldalra C:WindowsSystem32 meghajtó és törölje Hantek6022BLAMD641.SYS vagy hasonló, és próbálja meg újra a telepítést.

Install DRIVERS from Hantek.com, not from CD. DRIVER installation was a hustle, but I managed to get it working. You need to have button/switch next to USB port on oscilloscope in H position (P position is for logic channels). If you have problem with installation driver saying driver are not signed, go to C:WindowsSystem32driver and delete Hantek6022BLAMD641.SYS or similar and try the installation again.

Telepítse a DRÁVS-t a Hantek.com-ról, nem CD-ről. A sofőr telepítése gyors volt, de sikerült működésre bírnom. Meg kell gomb / kapcsoló mellett USB port oszcilloszkóp H pozícióban (P pozíció logikai csatornák). Ha problémája van a telepítőprogrammal, amely szerint az illesztőprogram nincs aláírva, menjen a következő oldalra C:WindowsSystem32 meghajtó és törölje Hantek6022BLAMD641.SYS vagy hasonló, és próbálja meg újra a telepítést.

Received: took 35 days to get to my country South Africa

Received: took 35 days to get to my country South Africa

Received: took 35 days to get to my country South Africa

great leads. but the scope has a little bit of noise

great leads. but the scope has a little bit of noise

great leads. but the scope has a little bit of noise

Adorei o produto, consegui pegar ele na promoção.. a única coisa que n achei de boa qualidade foram as garrinhas coloridas pra usar no analizador lógico, mas isso é relevante, fora isso achei muito bom

Adorei o produto, consegui pegar ele na promoção.. a única coisa que n achei de boa qualidade foram as garrinhas coloridas pra usar no analizador lógico, mas isso é relevante, fora isso achei muito bom

Adorei o produto, consegui pegar ele na promoção.. a única coisa que n achei de boa qualidade foram as garrinhas coloridas pra usar no analizador lógico, mas isso é relevante, fora isso achei muito bom

Definitely a good bang for your buck. Don't expect a great quality tool set for such a small price, but it'll definitely do the job for hobbyists or engineers on a small budget. You do get a LOT of stuff for little. The unit itself is nice and sturdy and has a mostly metal frame. The 2 supplied probes are probably quite cheap, though rated at 80MHz, but seem a good quality nonetheless. They also come with an adjustment tool and various colored rings for identification which is really handy. The logic analyzer probes are a bit more flimsy and a bunch of jumper cables are supplied for the wiring which... yeah isn't very great IMHO. Again: can't complain for such a price but I will replace the way too short jumper cables with something better ASAP. You do get two packs of 8 probes, so got plenty for a good while :) Beware that the advertised 20MHz (-3db) bandwidth, though maybe true for the analog part of the hardware, is not something this thing will sample in detail at all. At around 8Mhz you'll have ~6 samples (48/8) per waveform cycle so don't expect an accurate representation at or above this frequency. Frequency/timing measurement is still possible even at such low samples luckily though :) Finally I wanna give an free-and-open-source alternative to the software: OpenHantek. It's a better interface and is improved constantly but has the one major drawback of only going up to 30MSa/s so if you, like me, need to measure high frequencies you may be better off with the stock software.

Definitely a good bang for your buck. Don't expect a great quality tool set for such a small price, but it'll definitely do the job for hobbyists or engineers on a small budget. You do get a LOT of stuff for little. The unit itself is nice and sturdy and has a mostly metal frame. The 2 supplied probes are probably quite cheap, though rated at 80MHz, but seem a good quality nonetheless. They also come with an adjustment tool and various colored rings for identification which is really handy. The logic analyzer probes are a bit more flimsy and a bunch of jumper cables are supplied for the wiring which... yeah isn't very great IMHO. Again: can't complain for such a price but I will replace the way too short jumper cables with something better ASAP. You do get two packs of 8 probes, so got plenty for a good while :) Beware that the advertised 20MHz (-3db) bandwidth, though maybe true for the analog part of the hardware, is not something this thing will sample in detail at all. At around 8Mhz you'll have ~6 samples (48/8) per waveform cycle so don't expect an accurate representation at or above this frequency. Frequency/timing measurement is still possible even at such low samples luckily though :) Finally I wanna give an free-and-open-source alternative to the software: OpenHantek. It's a better interface and is improved constantly but has the one major drawback of only going up to 30MSa/s so if you, like me, need to measure high frequencies you may be better off with the stock software.

Definitely a good bang for your buck. Don't expect a great quality tool set for such a small price, but it'll definitely do the job for hobbyists or engineers on a small budget. You do get a LOT of stuff for little. The unit itself is nice and sturdy and has a mostly metal frame. The 2 supplied probes are probably quite cheap, though rated at 80MHz, but seem a good quality nonetheless. They also come with an adjustment tool and various colored rings for identification which is really handy. The logic analyzer probes are a bit more flimsy and a bunch of jumper cables are supplied for the wiring which... yeah isn't very great IMHO. Again: can't complain for such a price but I will replace the way too short jumper cables with something better ASAP. You do get two packs of 8 probes, so got plenty for a good while :) Beware that the advertised 20MHz (-3db) bandwidth, though maybe true for the analog part of the hardware, is not something this thing will sample in detail at all. At around 8Mhz you'll have ~6 samples (48/8) per waveform cycle so don't expect an accurate representation at or above this frequency. Frequency/timing measurement is still possible even at such low samples luckily though :) Finally I wanna give an free-and-open-source alternative to the software: OpenHantek. It's a better interface and is improved constantly but has the one major drawback of only going up to 30MSa/s so if you, like me, need to measure high frequencies you may be better off with the stock software.