Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (95)
  • Kép (4)
  • Videó (0)
  • Minden csillag
    • Minden csillag(95)
    • 5 Csillag(94)
    • 4 Csillag(1)
    • 3 Csillag(0)
    • 2 Csillag(0)
    • 1 Csillag(0)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 16/04/2019

    perfecto excelente

    Hozzászólások (1)
    Mutasd az eredetit
  • 19/12/2020

    Very Good

    Hozzászólások
    Mutasd az eredetit
  • 20/09/2020

    Praktický pomocník při obrábění tenkých součástek. Porovnání běžného hrotu s prodlouženým hrotem. Je vidět že se nástroj dostane blízko k navrtání a snáze se obrábí.

    Hozzászólások
    Mutasd az eredetit
  • TomVIP1
    DE
    14/09/2017

    Körnerspitze hat im vorderen Teil einen Rundlauf von einem 1/2 100 mm! Das ist ein sehr guter Wert! Körner ist gut verarbeitet, hat ein sauberes Finish. Würde ich wieder kaufen!

    Hozzászólások
    Mutasd az eredetit
  • 16/02/2019

    Excellent craftmanship and performance with near zero runout at a very good price. Nice, small point makes end facing simple. Only minus is that the protruding MT2 small end reduces my quill travel 1/2", but I guess that will be cut/ ground off one of these days.

    Hozzászólások
    Mutasd az eredetit
  • 08/08/2019

    Very well made product from look and finish. Theres one problem on my lathe: The MT2 shank is a few millimeters to short. I can't stroke back the tailstock far enought to release it. All other orderes MT2 shank parts from Banggood don't have this problem! Luckily I noticed the shank is not hardend, so I will bore in, tap a thread and just put a screw in - Problem solved.

    Hozzászólások
    Mutasd az eredetit
  • 07/04/2018

    Finish and appearance is exellent. The run out is almost undetectable, i.e., below 0.003 mm.

    Hozzászólások
    Mutasd az eredetit
  • 26/08/2017

    I needed a small live center for my MT2 tailstock. This live center is a perfect companion to my regular sized one (I like the size of it). The morse taper shank is a bit short and has no thread at the end. This can be easily fixed with a lathe. I'll add a threaded bore so I can put a bolt into it (for easier extraction) . The quality of the bearing is nothing to write home about. I'll see how it stands up to use. Glad I have it. The price is excellent.

    Hozzászólások
    Mutasd az eredetit
  • 05/02/2022

    pas de jeu propre tourne bien et en douceur , pas de jeu , cone mt2 qui va bien ..

    Hozzászólások
    Mutasd az eredetit
  • 24/08/2021

    Nagyszerű.

    Hozzászólások
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    Lehet, hogy érdekli

    recommendation for you
    • US$96.99
    • US$8.99
    • US$8.99
    • US$7.99
    • US$18.47
    • US$19.62
    • US$7.63
    • US$53.12
    • US$22.87
    • US$20.78
    • US$9.99
    • US$6.99
    • US$9.23
    • US$16.49
    • US$60.05
    • US$43.88
    • US$50.81
    • US$17.31