USB továbbító modul OPEN-SMART ESP8266 ESP-01S LINK V2.0 Wi-Fihez 2104 meghajtóval vélemények - Banggood Magyar online vásárlás

:

Download the

Banggood App

Töltse le az alkalmazást, hogy megkapja

3 USD kedvezményes kupon

Szállítás:

Nyelv:

Valuta:

Helló Bejelentkezés Csatlakozik
Bejelentkezés Csatlakozz hozzánk
Új vevő? Kezdd itt.
0

USB továbbító modul OPEN-SMART ESP8266 ESP-01S LINK V2.0 Wi-Fihez 2104 meghajtóval

US$7.99
~~US$9.99~~
Vásárolj most

Vásárlói vélemények

4.86 / 5

Az összes 21 vélemény megtekintése

5 csillag
18 (85.7%)
4 csillag
3 (14.3%)
3 csillag
0 (0%)
2 csillag
0 (0%)
1 csillag
0 (0%)

Írja meg a véleményét Szerezzen dupla értékelési pontot, ha Ön az első 3 közzétett értékelés egyike!

Minden vélemény (21)
Kép (2)
Videó (0)
Minden csillag
- Minden csillag(21)
- 5 Csillag(18)
- 4 Csillag(3)
- 3 Csillag(0)
- 2 Csillag(0)
- 1 Csillag(0)

Sorrend:

Legjobb áttekintés

Legjobb áttekintés
Leghasznosabb
Legfrissebb

Csak az Ön országából származó vélemények (Hungary)

|

Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

VideoLiamVIP3
GB
24/01/2020

Arrived safe and sound. First impressions were luke warm as the board look tatty, but it was just unwashed flux. There is a handy arrow ti assist you in getting the ESP01s plugged in the right way around, and be careful it is very easy to get wrong. To use it as a programer for the Arduino IDE, all you need to do is add a simple switch between IO0 and GND to get it in to flash mode. Simple.

Arrived safe and sound. First impressions were luke warm as the board look tatty, but it was just unwashed flux. There is a handy arrow ti assist you in getting the ESP01s plugged in the right way around, and be careful it is very easy to get wrong. To use it as a programer for the Arduino IDE, all you need to do is add a simple switch between IO0 and GND to get it in to flash mode. Simple.

Arrived safe and sound. First impressions were luke warm as the board look tatty, but it was just unwashed flux. There is a handy arrow ti assist you in getting the ESP01s plugged in the right way around, and be careful it is very easy to get wrong. To use it as a programer for the Arduino IDE, all you need to do is add a simple switch between IO0 and GND to get it in to flash mode. Simple.
0

Hozzászólások

Mutasd az eredetit
KamilVIP2
SK
25/04/2018

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.

I plan to use this adapter for ESP 8266 - 01. It looks OK, but there are missing any instructions. I have found driver on internet, so the driver in my PC is OK. Adapter itself could be OK, there is 5V to 3.3V conversion, but I was not able to upload software to ESP 01 board. Missing switch GPIO0 to GND (for software upload). My ESP01 module was not S type, so maybe this was a problem.
2

Hozzászólások (2)

Mutasd az eredetit

Show:

Teljes 0 oldalakat

Menj az oldalra

Megy

Lehet, hogy érdekli

recommendation for you