Vásárlói vélemények

Írja meg a véleményét
  • Minden vélemény (99)
  • Kép (8)
  • Videó (0)
  • Minden csillag
    • Minden csillag(99)
    • 5 Csillag(89)
    • 4 Csillag(9)
    • 3 Csillag(1)
    • 2 Csillag(0)
    • 1 Csillag(0)
Sorrend:
Legjobb áttekintés
  • Legjobb áttekintés
  • Leghasznosabb
  • Legfrissebb
Csak az Ön országából származó vélemények (Hungary)
|
Mutasd az eredetit

A felülvizsgálat egy részét automatikusan lefordították.

  • 16/01/2019

    This combo board has a 4 channel receiver for a motor, rudder, elevator and aileron. There are 6 outputs. Brushed motor solder pads. Brushless ESC solder pads. 2 servos (rudder and elevator). 2 connectors for the opposing ailerons. The receiver auto binds after 10 seconds. Setup a new model with FrSky D8 on the TX and set to bind. Then power the receiver. Wait for steady light, then power off. No mention current ratings. The speed control was able to handle a 0720 17000KV core-less motor. The largest LiPo battery tested was a 3.7V 250 mAh 35C. Alternately, a 1S brushless motor and a tiny ESC can be used. The onboard linear servos are relatively quick and pull 35g. The control horn, pushrod and servo should extend along a straight line. That way the push rod transfers the most movement (7mm) and results in enough control surface sweep. 2 tiny (1m) onboard JST connectors replaces an aileron wiring harness that wires a pair of micro linear servos to operate oppositely (which rolls the aircraft). Adding a pair of digital servos will cost about $20. There is no telemetry but the plane will drop if the signal is lost. The receiver doesn’t appear to have a low voltage cutoff so setting a timer is a good idea. Initially, the receiver seems a little jittery with nothing connected. After setting up the model, it calmed down considerably. Configuring the receiver is a function of a programmable transmitter. I’ve been using the TaranisQ X7.

    Hozzászólások (4)
    Mutasd az eredetit
  • 05/06/2019

    Good piece of electronics. Flying well in my small flying wing. Sometime it produce a little louder sound and electronics heat. If you do not move with servo, electronics overheat and stop working. A drop of "contact cleaner" almost eliminate such states.

    Hozzászólások (2)
    Mutasd az eredetit
  • 08/07/2019

    Nice little Frsky receiver with x2 servos two servo ports and builtin brushed esc 👌✌️ used it in the balsa 400mm cub 😊

    Hozzászólások
    Mutasd az eredetit
  • 18/05/2019

    Connects and and work well with my jumper T12. I fail connecting a servor with mini jst connector. It would handy to know what servor connector is the adequate one.

    Hozzászólások
    Mutasd az eredetit
  • 05/07/2019

    最高です。また購入します。ミニプレーンが作れます。ありがとうございました❗

    Hozzászólások
    Mutasd az eredetit
  • 11/04/2019

    Verpackung ok könnte besser geschützt sein Artikel aber super

    Hozzászólások
    Mutasd az eredetit
  • 14/03/2019

    Super Receiver for Micro Planes wird 1S and DSMx I put it in the BlackFlyer V2.

    Hozzászólások
    Mutasd az eredetit
  • 12/07/2019

    Great little 4in1 👍 servos are slightly stuttering but seems goos

    Hozzászólások
    Mutasd az eredetit
  • 29/03/2021

    I bought the dsm2/dsmx version. I had no problem binding it with my Spektrum 2.4GHz Module- equipped Futaba 8 channel heli transmitter. Prior to binding, the servos emitted a constant high-pitched electronic sound, however it disappeared when the bind was established. I have seen comments about these having some chatter at rest but this unit seems pretty good in that respect. As with anything this small, soldering wires to this tiny board will provide a real test of you equipment and skills. The solder pads are so small! The two linear servos on this board respond to the elevator and rudder (not aileron) channels of your transmitter. The two plugs on the board are for aileron and aux channel (such as flaps) as supplied, but can be changed to aileron and reverse aileron by jumping a connection on the back side of the circuit board. It's not a reflection on the product itself, but the packing was not adequate- a thin one-layer mylar pouch inside an unpadded small plastic bag. This item is too delicate to be treated in this manner. It is a testament to the services that transported this item that it arrived in functioning condition. Come on, BG! I'll gladly pay a bit more if it comes in a nice little box next time!

    Hozzászólások
    Mutasd az eredetit
  • 17/07/2021

    Ha az akkumulátor feszültsége 3,8v-nál kisebb, a kötés felszabadul, és a jel nem vezérlő (LED villog). Abban az időben csak a motor fog továbbra is forogni körülbelül 20-30%. A szervo nem mozdul. Van valami javulás a vevőkészülék konfigurációjában? Kérlek, mondd meg, hogy kell csinálni, ha van.

    Hozzászólások
    Mutasd az eredetit
Show:

    Teljes 0 oldalakat

    Menj az oldalra

    Lehet, hogy érdekli

    recommendation for you
    • Ft5 514
    • Ft7 356
    • Ft5 148
    • Ft17 658
    • Ft3 307
    • Ft2 743
    • Ft4 778
    • Ft18 394
    • Ft9 155
    • Ft13 978
    • Ft6 620
    • Ft5 514
    • Ft4 412
    • Ft3 676
    • Ft5 148
    • Ft11 401
    • Ft14 650
    • Ft4 412