The unit arrived well packaged & protected. No rust issues, but I did have to clean a decent amount of oil & a bit more machine fouling than I believe should be acceptable on any type of part being labeled precision. The chuck mounted up to my existing Little Machine Shop adapter plate. The first item i tossed in the chuck was a piece of 6mm Brass Round Bar & with not much effort I was able to have it centered to 0.0005" My only complaint is 2 of the 4 chuck jaws were not completely machined & they stopped short of completely facing off the face of the jaws. Pictures included will show the facing issue which I will turn & Face again on my own. At this point it is a product I would definitely purchase again in the future.

The unit arrived well packaged & protected. No rust issues, but I did have to clean a decent amount of oil & a bit more machine fouling than I believe should be acceptable on any type of part being labeled precision. The chuck mounted up to my existing Little Machine Shop adapter plate. The first item i tossed in the chuck was a piece of 6mm Brass Round Bar & with not much effort I was able to have it centered to 0.0005" My only complaint is 2 of the 4 chuck jaws were not completely machined & they stopped short of completely facing off the face of the jaws. Pictures included will show the facing issue which I will turn & Face again on my own. At this point it is a product I would definitely purchase again in the future.

The unit arrived well packaged & protected. No rust issues, but I did have to clean a decent amount of oil & a bit more machine fouling than I believe should be acceptable on any type of part being labeled precision. The chuck mounted up to my existing Little Machine Shop adapter plate. The first item i tossed in the chuck was a piece of 6mm Brass Round Bar & with not much effort I was able to have it centered to 0.0005" My only complaint is 2 of the 4 chuck jaws were not completely machined & they stopped short of completely facing off the face of the jaws. Pictures included will show the facing issue which I will turn & Face again on my own. At this point it is a product I would definitely purchase again in the future.

A valódi termék sokkal jobb, mint a megjelenített egy. 100mm-es méretűt rendeltem. Nagyon jól megmunkált. De szerelési (hátsó) oldalon más, mint a fotók - 4 lyukak 90 fok helyett 3lyukak 60 fok.

Real product is way BETTER than displayed one. I ordered 100mm size. Very well machined. But mounting (back) side is different, than on photos - 4 holes 90 deg instead of 3holes 60 deg.

A valódi termék sokkal jobb, mint a megjelenített egy. 100mm-es méretűt rendeltem. Nagyon jól megmunkált. De szerelési (hátsó) oldalon más, mint a fotók - 4 lyukak 90 fok helyett 3lyukak 60 fok.

These Sanou chucks are absolutely excellent value for money. They are made of high quality cast iron with hardened jaws which are excellent for holding all types of machinable steels. They have high precision made components, operate smoothly and brilliant finishes. Great for both manual lathes and CNC machines. I have bought several different Sanou chucks now and I am sticking to this brand because they are so good. Recomended in every way!

These Sanou chucks are absolutely excellent value for money. They are made of high quality cast iron with hardened jaws which are excellent for holding all types of machinable steels. They have high precision made components, operate smoothly and brilliant finishes. Great for both manual lathes and CNC machines. I have bought several different Sanou chucks now and I am sticking to this brand because they are so good. Recomended in every way!

These Sanou chucks are absolutely excellent value for money. They are made of high quality cast iron with hardened jaws which are excellent for holding all types of machinable steels. They have high precision made components, operate smoothly and brilliant finishes. Great for both manual lathes and CNC machines. I have bought several different Sanou chucks now and I am sticking to this brand because they are so good. Recomended in every way!

Gostei bastante e recomendo. É possível conseguir 0 centésimos de batimento com paciência. Único problema é que a face frontal das castanhas não foram retificadas corretamente pois há diferença entre as 4. A minha é de 80 mm, perfeita para peças pequenas

Gostei bastante e recomendo. É possível conseguir 0 centésimos de batimento com paciência. Único problema é que a face frontal das castanhas não foram retificadas corretamente pois há diferença entre as 4. A minha é de 80 mm, perfeita para peças pequenas

Gostei bastante e recomendo. É possível conseguir 0 centésimos de batimento com paciência. Único problema é que a face frontal das castanhas não foram retificadas corretamente pois há diferença entre as 4. A minha é de 80 mm, perfeita para peças pequenas

San Ou K72-80,80mm OD test metrikus független 4 állkapocs tok (nem 3" = 76,2 mm). Szerelt Boxford eszterga. Jól kész szerszám megfelel az ajánlott célra ( nemvasfémek és lágyabb anyagok, pl. alumínium, műanyag, fa stb.) Fogók vasfém munkadarabok megfelelően,azonban,a megcsúszásának veszélye a munkadarabot elfordítva okozhat nyíró károsodást az állkapocs tartó arcok.Tedd ezt saját belátása szerint.Megjegyzendő, hogy a 80mm tokmány (K72-80) egy 3 pont /3 csavaros szerelés mintázata a fényképeken látható.Egy külön tokmány adaptert lehet vásárolni vagy gyártani, hogy megfeleljen az adott eszterga.A rögzítőfőnök/karima 55mm átmérőjű x 4 mm magasságú, 3 csavaros szerelési minta 120 °-kal egymástól.Ajánlott elem.

San Ou K72-80.80mm OD body metric independent 4-jaw chuck(not a 3" chuck (3" = 76.2mm).Mounted on Boxford lathe.Well finished tool compliant to its recommended purpose( holding of non-ferrous metals and softer materials eg: aluminium,plastic,wood etc.) Clamps ferrous metal work pieces adequately,however,risk of slippage of the workpiece being turned may result in shearing damage on the jaw holding faces.Do so at your own discretion.Note that the 80mm chuck (K72-80) has a 3 point /3 screw mounting pattern as shown in the photographs.A separate chuck adapter may have to be purchased or fabricated to suit your particular lathe.Mounting boss/flange is 55mm diameter x 4 mm height,3 screw mounting pattern at 120º from each one another.Recommended item.

San Ou K72-80,80mm OD test metrikus független 4 állkapocs tok (nem 3" = 76,2 mm). Szerelt Boxford eszterga. Jól kész szerszám megfelel az ajánlott célra ( nemvasfémek és lágyabb anyagok, pl. alumínium, műanyag, fa stb.) Fogók vasfém munkadarabok megfelelően,azonban,a megcsúszásának veszélye a munkadarabot elfordítva okozhat nyíró károsodást az állkapocs tartó arcok.Tedd ezt saját belátása szerint.Megjegyzendő, hogy a 80mm tokmány (K72-80) egy 3 pont /3 csavaros szerelés mintázata a fényképeken látható.Egy külön tokmány adaptert lehet vásárolni vagy gyártani, hogy megfeleljen az adott eszterga.A rögzítőfőnök/karima 55mm átmérőjű x 4 mm magasságú, 3 csavaros szerelési minta 120 °-kal egymástól.Ajánlott elem.

Excellent product. Even better than described: The tightening tool has a security spring preventing the tool to be left on the chuck. I had done that on my previous 3/4 jaws to prevent accidents. The quality is very good, it gives an overall impression of serious construction and the run-out is ok for such a small machine accessory. Note that the Alen screws cannot be used on Chinese mini lathe, you need to prepare 6 mm x 30 studs as shown.

Excellent product. Even better than described: The tightening tool has a security spring preventing the tool to be left on the chuck. I had done that on my previous 3/4 jaws to prevent accidents. The quality is very good, it gives an overall impression of serious construction and the run-out is ok for such a small machine accessory. Note that the Alen screws cannot be used on Chinese mini lathe, you need to prepare 6 mm x 30 studs as shown.

Excellent product. Even better than described: The tightening tool has a security spring preventing the tool to be left on the chuck. I had done that on my previous 3/4 jaws to prevent accidents. The quality is very good, it gives an overall impression of serious construction and the run-out is ok for such a small machine accessory. Note that the Alen screws cannot be used on Chinese mini lathe, you need to prepare 6 mm x 30 studs as shown.

as always very well made !

as always very well made !

as always very well made !

Vema sam zadovoljan kako je napravljen sobzirom na cenu od 78.27 evra sa raznim popustima. Very satisfied

Vema sam zadovoljan kako je napravljen sobzirom na cenu od 78.27 evra sa raznim popustima. Very satisfied

Vema sam zadovoljan kako je napravljen sobzirom na cenu od 78.27 evra sa raznim popustima. Very satisfied

The quality and design looks perfect.

The quality and design looks perfect.

The quality and design looks perfect.

Good.

Good.

Good.