I connected to the equipment Flysky FS-I6. Quad Eachine H8 Mini

I connected to the equipment Flysky FS-I6. Quad Eachine H8 Mini

I connected to the equipment Flysky FS-I6. Quad Eachine H8 Mini

Attention! The product works with certain settings. Settings for FlySky FS-TH9S (Turnigy 9X, iMAX-TH9X): 1)SYSTEM SETTING \ TYPE SELE \ HELI \ HELI-1 2)2) SYSTEM SETTING \ MODEUAT \ PPM 3)SYSTEM SETTING \ STICK SET \ MODE 2 (Question about “REVERSE THR?” press the exit button) 4)FUNCTION SETTING (1\2)\ E. POIN (changing all on 120%) save settings \ switch off \ plug-in module \ binding \ go fly Для русскоязычных пользователей. Создаете модель с указанными выше настройками. Сохраняете настройки. Отключаете аппаратуру от питания, вставляете модуль. Включаете и биндите коптер по инструкции (ссылка на нее на странице продукта)

Attention! The product works with certain settings. Settings for FlySky FS-TH9S (Turnigy 9X, iMAX-TH9X): 1)SYSTEM SETTING \ TYPE SELE \ HELI \ HELI-1 2)2) SYSTEM SETTING \ MODEUAT \ PPM 3)SYSTEM SETTING \ STICK SET \ MODE 2 (Question about “REVERSE THR?” press the exit button) 4)FUNCTION SETTING (1\2)\ E. POIN (changing all on 120%) save settings \ switch off \ plug-in module \ binding \ go fly Для русскоязычных пользователей. Создаете модель с указанными выше настройками. Сохраняете настройки. Отключаете аппаратуру от питания, вставляете модуль. Включаете и биндите коптер по инструкции (ссылка на нее на странице продукта)

Attention! The product works with certain settings. Settings for FlySky FS-TH9S (Turnigy 9X, iMAX-TH9X): 1)SYSTEM SETTING \ TYPE SELE \ HELI \ HELI-1 2)2) SYSTEM SETTING \ MODEUAT \ PPM 3)SYSTEM SETTING \ STICK SET \ MODE 2 (Question about “REVERSE THR?” press the exit button) 4)FUNCTION SETTING (1\2)\ E. POIN (changing all on 120%) save settings \ switch off \ plug-in module \ binding \ go fly Для русскоязычных пользователей. Создаете модель с указанными выше настройками. Сохраняете настройки. Отключаете аппаратуру от питания, вставляете модуль. Включаете и биндите коптер по инструкции (ссылка на нее на странице продукта)

This is what I've been waiting for. No need for crappy proprietary Controllers any longer, I just can use my Taranis for flying every mini Quadcopter I own <3 I use it with a Eachine E010 a.k.a. the Inductrix clone: http://www.banggood.com/Eachine-E010-Mini-2_4G-4CH-6-Axis-Headless-Mode-RC-Quadcopter-RTF-p-1066972.html?p=430714520645201404S1 It works just awesome! Binding is quick and easy. :)

This is what I've been waiting for. No need for crappy proprietary Controllers any longer, I just can use my Taranis for flying every mini Quadcopter I own <3 I use it with a Eachine E010 a.k.a. the Inductrix clone: http://www.banggood.com/Eachine-E010-Mini-2_4G-4CH-6-Axis-Headless-Mode-RC-Quadcopter-RTF-p-1066972.html?p=430714520645201404S1 It works just awesome! Binding is quick and easy. :)

This is what I've been waiting for. No need for crappy proprietary Controllers any longer, I just can use my Taranis for flying every mini Quadcopter I own <3 I use it with a Eachine E010 a.k.a. the Inductrix clone: http://www.banggood.com/Eachine-E010-Mini-2_4G-4CH-6-Axis-Headless-Mode-RC-Quadcopter-RTF-p-1066972.html?p=430714520645201404S1 It works just awesome! Binding is quick and easy. :)

Perfectly Bind Eachine E010 with Taranis. hassle free installation. Now I can control my Eachine E010 precisely and keep most of the feature like Flip, Headless, RTL, Rebind.

Perfectly Bind Eachine E010 with Taranis. hassle free installation. Now I can control my Eachine E010 precisely and keep most of the feature like Flip, Headless, RTL, Rebind.

Perfectly Bind Eachine E010 with Taranis. hassle free installation. Now I can control my Eachine E010 precisely and keep most of the feature like Flip, Headless, RTL, Rebind.

This works great with the new Taranis Q X7 right out of the box without any firmware upgrades or anything. Just need to set it up with PPM, channels 1-12 and you are ready to go. Love it!

This works great with the new Taranis Q X7 right out of the box without any firmware upgrades or anything. Just need to set it up with PPM, channels 1-12 and you are ready to go. Love it!

This works great with the new Taranis Q X7 right out of the box without any firmware upgrades or anything. Just need to set it up with PPM, channels 1-12 and you are ready to go. Love it!

Hello, I want to tell you goods, but I have a problem. If I plug in the TX Modul into my Taranis X9D plus and I switch on my Taranis - the LED doesn't shine. Inside it's move to external HF and I changed to written settings. I checked the modul. Volts are okay. The Taranis is okay too - because I checked with other moduls - this starts directly. Thanks for your help. CU Frank

Hello, I want to tell you goods, but I have a problem. If I plug in the TX Modul into my Taranis X9D plus and I switch on my Taranis - the LED doesn't shine. Inside it's move to external HF and I changed to written settings. I checked the modul. Volts are okay. The Taranis is okay too - because I checked with other moduls - this starts directly. Thanks for your help. CU Frank

Hello, I want to tell you goods, but I have a problem. If I plug in the TX Modul into my Taranis X9D plus and I switch on my Taranis - the LED doesn't shine. Inside it's move to external HF and I changed to written settings. I checked the modul. Volts are okay. The Taranis is okay too - because I checked with other moduls - this starts directly. Thanks for your help. CU Frank

bough this so I could use my X7 to control my E010 whoop, works well after looking up manual. make sure you set up a new model with External RF set to PPM, channel range CH1-12, to connect to the E010 pull sticks to the bottom right when turning your controller on, this should remember your drone but when changing battery's you will have to restart your controller or select another model then switch back.

bough this so I could use my X7 to control my E010 whoop, works well after looking up manual. make sure you set up a new model with External RF set to PPM, channel range CH1-12, to connect to the E010 pull sticks to the bottom right when turning your controller on, this should remember your drone but when changing battery's you will have to restart your controller or select another model then switch back.

bough this so I could use my X7 to control my E010 whoop, works well after looking up manual. make sure you set up a new model with External RF set to PPM, channel range CH1-12, to connect to the E010 pull sticks to the bottom right when turning your controller on, this should remember your drone but when changing battery's you will have to restart your controller or select another model then switch back.

installation simple read the instructions. Important (AETR). 1 Create new model.(p1 0f 13) 2 Check AETR default (p1 of 7) 3 Switch of internal RF, switch on external RF PPM CH range 1 to 12 (p2 of 13) 4 Check Mixers AETR all at 100 (p6 of 13) 5 Calibrate Sticks (p7 of 7) 6 Switch off TX fit module with care switch on TX after a few seconds the green LED on the module should flash and become solid. 7 switch off TX. ready to go see below and use the notes on the Banggood product guide The multiprotocol TX module i fitted to my old FrskyTaranis X9D software version opentx-x9d-v1. 1. 02. works well. I have an old Eachine H8 mini and a new one, they bind using H8(C) Ali Right and Ele Up, switch .on TX when the H8 stops flashing release the stick and fly. Then I tried the JJRC H8C I used the JJRC Eli Up, switch on TX, this was fine. need to sort the flips ect: and try auto rebind when you go out of range into the wind as the toy TX rebinds when the wind blows you back in range. That's handy.

installation simple read the instructions. Important (AETR). 1 Create new model.(p1 0f 13) 2 Check AETR default (p1 of 7) 3 Switch of internal RF, switch on external RF PPM CH range 1 to 12 (p2 of 13) 4 Check Mixers AETR all at 100 (p6 of 13) 5 Calibrate Sticks (p7 of 7) 6 Switch off TX fit module with care switch on TX after a few seconds the green LED on the module should flash and become solid. 7 switch off TX. ready to go see below and use the notes on the Banggood product guide The multiprotocol TX module i fitted to my old FrskyTaranis X9D software version opentx-x9d-v1. 1. 02. works well. I have an old Eachine H8 mini and a new one, they bind using H8(C) Ali Right and Ele Up, switch .on TX when the H8 stops flashing release the stick and fly. Then I tried the JJRC H8C I used the JJRC Eli Up, switch on TX, this was fine. need to sort the flips ect: and try auto rebind when you go out of range into the wind as the toy TX rebinds when the wind blows you back in range. That's handy.

installation simple read the instructions. Important (AETR). 1 Create new model.(p1 0f 13) 2 Check AETR default (p1 of 7) 3 Switch of internal RF, switch on external RF PPM CH range 1 to 12 (p2 of 13) 4 Check Mixers AETR all at 100 (p6 of 13) 5 Calibrate Sticks (p7 of 7) 6 Switch off TX fit module with care switch on TX after a few seconds the green LED on the module should flash and become solid. 7 switch off TX. ready to go see below and use the notes on the Banggood product guide The multiprotocol TX module i fitted to my old FrskyTaranis X9D software version opentx-x9d-v1. 1. 02. works well. I have an old Eachine H8 mini and a new one, they bind using H8(C) Ali Right and Ele Up, switch .on TX when the H8 stops flashing release the stick and fly. Then I tried the JJRC H8C I used the JJRC Eli Up, switch on TX, this was fine. need to sort the flips ect: and try auto rebind when you go out of range into the wind as the toy TX rebinds when the wind blows you back in range. That's handy.

The modul is used in a FrSky Taranis Q X7 to control an Eachine E010 mini quadcopter.

The modul is used in a FrSky Taranis Q X7 to control an Eachine E010 mini quadcopter.

The modul is used in a FrSky Taranis Q X7 to control an Eachine E010 mini quadcopter.

J'ai monté ce module sur ma Taranis X9D pour piloter un H8 mini. J'ai également réussi à le bricoler pour m'en servir ma radio TGY-i6 (ou FS-i6) La modif est à voir ici : https://www.adal.club/showthread.php?tid=507

J'ai monté ce module sur ma Taranis X9D pour piloter un H8 mini. J'ai également réussi à le bricoler pour m'en servir ma radio TGY-i6 (ou FS-i6) La modif est à voir ici : https://www.adal.club/showthread.php?tid=507

J'ai monté ce module sur ma Taranis X9D pour piloter un H8 mini. J'ai également réussi à le bricoler pour m'en servir ma radio TGY-i6 (ou FS-i6) La modif est à voir ici : https://www.adal.club/showthread.php?tid=507