A Mini Mustang P-51D, RC repülőgép,Microscope,Eachine Mini F4U legjobb ajánlatai

Eachine Mini Mustang P-51D V2 761-5 EPP 400mm Fesztávolság 2.4G 6-tengelyes Gyro RC Repülőgép Edző Rögzített Szárny BNF/RTF One Key Return Kompatibilis az DSM S-BUS Protokollal Kezdők számára

US$108.99 US$195.59

Q: Please could you tell me more about this transmitter? Is it mode 4 (left stick: ailerons+throttle, righ stick: rudder+elevator) or mode 2 (left stick: rudder+throttle, right stick: ailerons+elevator)? Thank you for all answers...

Kérdezte tomasweiner tovább 2020-09-02 12:19:18

socmell si

2024-01-24 01:57:31 Hasznos

Beküldés

Válaszok (4)

tomasweiner 03/10/2020

The package arrived almost undamaged. The polysterene case was slightly cracked but despite this, the microscope and all parts were undamaged. In generall, the microsocope is working nicely. There are several things which are not ideal for me and might be better: 1) I received the US power plug which is not used in the Czech Republic. I replaced a new plug in the circular light and bought a new power adapter for the camera. 2) The four rubber buttons on the lower side of the base were not in the same plane so the stand was slightly swaying. One of the rubber buttons had its hole more deeply cut in the base so I added a metal washer to partly repair this. Other way how to fix this problem might be to slightly cut the rubber buttons. 3) The computer software (USB connection) for the camera do not allow to manually set the exposure, white ballance and ISO number. The menu of the camera allow to set only slight exposure correction and white ballance correction (only if connected via hdmi). Despite this, all attempts to change white ballance in the camera were unsuccesfull and all images have the same color tone in various white ballance settings (white ballance settings seems to be not working properly). The fact that the camera do not allow full resolution (34 megapixel) images via USB to the computer I consider as very limiting. I hope that all these things (manual exposure, white ballance, full resolution via USB...) will be modified and upgraded in a new (forthcomming) models of microscope camera and software. 3) The thread for auxilliary lens seem to be made rather inaccurately (slightly crooked) and I am afraid it will have rather short lifetime if auxilliary lens replaced often. 4) The stand is slightly unstable if the arms are set to the maximum extent but this can be easily fixed by adding some weight on the base...General comment: Despite all slight disadvantages mentioned above, I am happy with this product. I would recommend to buy it.

HAYEAR 3,5X 7X 45X 90X dupla gém állvány zoom szimul fókuszú trinokuláris sztereó mikroszkóp + 34 MP kameramikroszkóp ipari PCB javításhoz

US$769.64 US$805.99

2

Hozzászólások (1)

Eachine Mini Mustang P-51D V2 761-5 EPP 400mm Fesztávolság 2.4G 6-tengelyes Gyro RC Repülőgép Edző Rögzített Szárny BNF/RTF One Key Return Kompatibilis az DSM S-BUS Protokollal Kezdők számára

US$108.99 US$195.59

Q: O received Eachine p51d yesterday. The maiden flight will be later because I must fix at least one problem at the first. My elevator seems to have very small up and down movements (tested in non-stabilized expert mode). Please could you tell me in which pithole in the servo lever is set the steel wire for elevator? Both rudder and elevator servos are visible in opening on lower side of the airplane. In my p51 is the elevator on the first pinhole on servo lever (more close to the servo) whereas the rudder is on the second pinhole on the servo lever (more distatn to the servo). Please can someone tell me which position of elevator steel wire was set from the factory on the servo lever??? Thank you for all comments and advices...

Kérdezte tomasweiner tovább 2020-09-12 08:43:05

Robbiedobbie79 I agree with the first answer. War planes in general are super touchy and at this size little movements make a big difference. Both my factory positions are middle hole. That being said I would use the u bends in the rods first the mechanically trim the plane close then use the transmitter to fine tune. Also the plane will act weird at lower speed so keep throttle up and on beginner mode until trimmed right.

2022-02-14 06:56:51 Hasznos

Beküldés

Válaszok (2)

tomasweiner 11/09/2020

The package was delivered undamaged. The plane is looking nice and the all electonics including gyro-stabilization seems to be working properly. The maiden flight is planned later because I need to fix one or two possible problems at the first: 1) The elevator have very small up and down movements when compared with the rudder (in non-stabilized expert mode as well as in all three modes…). There is an opening near aileron servo on the lower side of the plane which enable to observe rudder and elevator servos. In my p51, the steel wire of rudder is connected on the second pinhole in the servo lever, but the elevator is connected on the first pinhole of the servo lever (more closer to the servo). This is probably the cause of small elevator movement. I have attached the photograph, which show the same detail in my p51 and the same detail of the machine reviewed by Brian Phillips. In the p51 of Brian Phillips are both first pinholes of rudder/elevator servo levers free and both rudder and elevator must be connected on the second pinhole (more distant to the servo). I am afraid I will be not able to fly this plane safely with a such small elevator movement. Please can someone advice me how to fix this problem without cutting into the airplane? I think this is a manufacturing error… 2) The moving surfaces of ailerons are connected to the wing by the very thin epp with many cracks and chaotic holes (epp connections of rudder and elevator looks better in my p51D). Maybe it will be necessafry to fix them better but I am not sure. As judged from photographs in various reviews here, other Eachine mini Mustangs seem to have slightly more thick epp in aileron connections. The product photographs show alternation of epp strips and strips without epp in the aileron connection. Please can someone advice me some suitable foam glue which is sufficiently flexible for fixing aileron connection (enabling easy aileron movement)? I would be grateful for all advices (see photographs..)