Nagyon jó repülésirányító!

Very good flight controller!

Nagyon jó repülésirányító!

Jó minőségűnek tűnik.

Looks good quality.

Jó minőségűnek tűnik.

Még nem próbáltam. Gyors szállítás.

Looks good. Not tried yet. Fast shipping. Thanks.

Még nem próbáltam. Gyors szállítás.

Szép FC kiegészítéssel baro és vaku a fekete doboz, sok uarts rendelkezésre álló és alapvető lyukak NYÁK menetes vezetékek forrasztás előtt, ami miatt sooo sokkal könnyebb, hogy vezetékes fel. Van egy dedikált pin ki TX5 GPS és működik Caddix / DJI légi egység is. Nagy kis replika pin ki NYÁK küldött is minden csapok címkézett, hogy mind hasznos, és hogy egy tisztességes kulcstartó mellett utána. Használtak két eddig, és valószínűleg vesz egy másik helyett alapvető tiro alsó fcs valami sokkal, sokkal jobb. Csak csalódást nem INAV szoftver látom, hogy ez még teszi egy nagyon teljes kis fickó! Is kell ad egy kiáltást, hogy jemchu(?) 20 esc fórumon azonos lyukak drót menetelés

Nice FC with addition of baro and flash for blackbox, lots of uarts available and essential holes in PCB to thread wires before soldering which makes it sooooo much easier to get wired up. Has a dedicated pin out on TX5 for GPS and works with Caddix/DJI air unit as well. Great little replica pin out PCB sent as well with all pins labelled that's both useful and make a decent keyring addition afterwards. Have used two so far and will likely buy another to replace basic tyro low end fcs with something much, much better. Only disappointment is no INAV firmware I can see for this yet which would make it a very complete little fellow! Also have to give a shout out to jemchu(?) 20 esc board with same holes for wire threading

Szép FC kiegészítéssel baro és vaku a fekete doboz, sok uarts rendelkezésre álló és alapvető lyukak NYÁK menetes vezetékek forrasztás előtt, ami miatt sooo sokkal könnyebb, hogy vezetékes fel. Van egy dedikált pin ki TX5 GPS és működik Caddix / DJI légi egység is. Nagy kis replika pin ki NYÁK küldött is minden csapok címkézett, hogy mind hasznos, és hogy egy tisztességes kulcstartó mellett utána. Használtak két eddig, és valószínűleg vesz egy másik helyett alapvető tiro alsó fcs valami sokkal, sokkal jobb. Csak csalódást nem INAV szoftver látom, hogy ez még teszi egy nagyon teljes kis fickó! Is kell ad egy kiáltást, hogy jemchu(?) 20 esc fórumon azonos lyukak drót menetelés

schnell geliefert, gute Qualität.

schnell geliefert, gute Qualität.

schnell geliefert, gute Qualität.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

Milyen egy félelmetes kis FC a 10volt bec nagyon hasznos, hogy a rohanás tank mini. Nagyon tiszta, nincs zaj a VTX-en. Szuper boldog.

What an awesome little FC the 10volt bec is very helpful with the Rush tank mini. Very clean no noise on the VTX. Super happy.

Milyen egy félelmetes kis FC a 10volt bec nagyon hasznos, hogy a rohanás tank mini. Nagyon tiszta, nincs zaj a VTX-en. Szuper boldog.