Input : Standard PWM Protocol Output : Relay Switch It uses TAKAMISAWA A5W-K Relay which is 2P2T. Able to handle DC30V 1A Max 2A.. You can find manual here http://www.weclonline.com/downloads/pdf/07-01-4005.pdf

Input : Standard PWM Protocol Output : Relay Switch It uses TAKAMISAWA A5W-K Relay which is 2P2T. Able to handle DC30V 1A Max 2A.. You can find manual here http://www.weclonline.com/downloads/pdf/07-01-4005.pdf

Input : Standard PWM Protocol Output : Relay Switch It uses TAKAMISAWA A5W-K Relay which is 2P2T. Able to handle DC30V 1A Max 2A.. You can find manual here http://www.weclonline.com/downloads/pdf/07-01-4005.pdf

product seems fine but pins on the relay are so tiny, I do not know how to easily make connections to this device

product seems fine but pins on the relay are so tiny, I do not know how to easily make connections to this device

product seems fine but pins on the relay are so tiny, I do not know how to easily make connections to this device

A DPDT relay RC switch makes it convenient to switch two devices simultaneously. A red LED indicates connection to the transmitter and a green LED indicates ON position. The relay switches about 2 amps current. works fine as described.

A DPDT relay RC switch makes it convenient to switch two devices simultaneously. A red LED indicates connection to the transmitter and a green LED indicates ON position. The relay switches about 2 amps current. works fine as described.

A DPDT relay RC switch makes it convenient to switch two devices simultaneously. A red LED indicates connection to the transmitter and a green LED indicates ON position. The relay switches about 2 amps current. works fine as described.

Good product.

Good product.

Good product.

For switching galvanically isolated from the control signals of the load circuits, an electromechanical relay is a good thing. The relay is very compact. Colored small LEDs on the board indicate the presence of power and the status of contacts. Two pairs of contacts, if included in parallel, will, if desired, increase the permissible switched current. According to the datasheet, if I understood correctly, each relay contact is capable of switching current up to 2A at a DC voltage of up to 30V. When the switching voltage increases, the permissible switching current decreases (see datasheet). According to the datasheet, the control voltage to the coil of the relay itself can vary from 1.5 to 48V DC. However, the power supply to the relay control circuit from the PWM channel signal (on the printed circuit board), according to the Banggood Listing, should be 5V. I really hope that the 6V (RC models with powerful servos) relay control circuit will also successfully hold. Datashit looked here: www.weclonline.com/downloads/pdf/07-01-4005.pdf - thanks to the user who provided this address in his comment here.

For switching galvanically isolated from the control signals of the load circuits, an electromechanical relay is a good thing. The relay is very compact. Colored small LEDs on the board indicate the presence of power and the status of contacts. Two pairs of contacts, if included in parallel, will, if desired, increase the permissible switched current. According to the datasheet, if I understood correctly, each relay contact is capable of switching current up to 2A at a DC voltage of up to 30V. When the switching voltage increases, the permissible switching current decreases (see datasheet). According to the datasheet, the control voltage to the coil of the relay itself can vary from 1.5 to 48V DC. However, the power supply to the relay control circuit from the PWM channel signal (on the printed circuit board), according to the Banggood Listing, should be 5V. I really hope that the 6V (RC models with powerful servos) relay control circuit will also successfully hold. Datashit looked here: www.weclonline.com/downloads/pdf/07-01-4005.pdf - thanks to the user who provided this address in his comment here.

For switching galvanically isolated from the control signals of the load circuits, an electromechanical relay is a good thing. The relay is very compact. Colored small LEDs on the board indicate the presence of power and the status of contacts. Two pairs of contacts, if included in parallel, will, if desired, increase the permissible switched current. According to the datasheet, if I understood correctly, each relay contact is capable of switching current up to 2A at a DC voltage of up to 30V. When the switching voltage increases, the permissible switching current decreases (see datasheet). According to the datasheet, the control voltage to the coil of the relay itself can vary from 1.5 to 48V DC. However, the power supply to the relay control circuit from the PWM channel signal (on the printed circuit board), according to the Banggood Listing, should be 5V. I really hope that the 6V (RC models with powerful servos) relay control circuit will also successfully hold. Datashit looked here: www.weclonline.com/downloads/pdf/07-01-4005.pdf - thanks to the user who provided this address in his comment here.

Excellent product thank you Banggood

Excellent product thank you Banggood

Excellent product thank you Banggood

leggero ma senza un minimo di specifiche tecniche

leggero ma senza un minimo di specifiche tecniche

leggero ma senza un minimo di specifiche tecniche

Apró és rendkívül hasznos vezérlésére szinte bármit, még a szervo jelek kapcsolására is. Vannak elszigetelt DDT kapcsoló kapcsolatok, így rengeteg lehetőség áll rendelkezésre.

Tiny and extremely useful for controlling just about anything, even switching servo signals about. There are isolated DPDT switching contacts, so plenty of options available.

Apró és rendkívül hasznos vezérlésére szinte bármit, még a szervo jelek kapcsolására is. Vannak elszigetelt DDT kapcsoló kapcsolatok, így rengeteg lehetőség áll rendelkezésre.

2021. június 8. előtt szállítják

Estimated to ship before June 8, 2021

2021. június 8. előtt szállítják

Jó termék. Könnyen kezelhető és nagyon kicsi.

Good product. Easy to handle and very small.

Jó termék. Könnyen kezelhető és nagyon kicsi.