LilyGo TTGO T-Display are really nice ESP32 boards. I've bought quite a few from Banggood and they all arrived quickly, safely and all work without fault. Be aware the USB interface is USB C (nicer than micro-USB) and with Arduino there is a reliable upload. You will need to install the CP210x USB to UART Bridge VCP Drivers from silabs.com for the USB port to be recognised on your computer. The colour ST7789V display is really nice - and although it takes up a few of the ESP32 pins, there are enough available for us to use SPI + I2S + I2S + others. NB: GPIO36 to 39 are input only. The blue power LED is (annoyingly) not programmable. The LCD backlight can be controlled as a LED on GPIO4. If you use the recommended TFT_eSPI display driver library and use a full screen-sized Sprite for the display then you can get flicker free >40FPS without effort. A LIPO battery connected to the connector underneath can be charged by the USB, and disconnecting/reconnecting either does not crash the ESP32. There is hardware battery management for charging but not for discharging, and it carries on draining until the ESP32 crashes, so, if you are powering just on an unprotected LiPo battery you may want to prevent damage to your LiPo by including some code to test the battery voltage (a simple function call) and go into deep sleep (very low power) if eg battery goes < 3.2V. I have designed a good 3D printable case available free here: https://www.thingiverse.com/thing:4501444 Have fun! PJMI

LilyGo TTGO T-Display are really nice ESP32 boards. I've bought quite a few from Banggood and they all arrived quickly, safely and all work without fault. Be aware the USB interface is USB C (nicer than micro-USB) and with Arduino there is a reliable upload. You will need to install the CP210x USB to UART Bridge VCP Drivers from silabs.com for the USB port to be recognised on your computer. The colour ST7789V display is really nice - and although it takes up a few of the ESP32 pins, there are enough available for us to use SPI + I2S + I2S + others. NB: GPIO36 to 39 are input only. The blue power LED is (annoyingly) not programmable. The LCD backlight can be controlled as a LED on GPIO4. If you use the recommended TFT_eSPI display driver library and use a full screen-sized Sprite for the display then you can get flicker free >40FPS without effort. A LIPO battery connected to the connector underneath can be charged by the USB, and disconnecting/reconnecting either does not crash the ESP32. There is hardware battery management for charging but not for discharging, and it carries on draining until the ESP32 crashes, so, if you are powering just on an unprotected LiPo battery you may want to prevent damage to your LiPo by including some code to test the battery voltage (a simple function call) and go into deep sleep (very low power) if eg battery goes < 3.2V. I have designed a good 3D printable case available free here: https://www.thingiverse.com/thing:4501444 Have fun! PJMI

LilyGo TTGO T-Display are really nice ESP32 boards. I've bought quite a few from Banggood and they all arrived quickly, safely and all work without fault. Be aware the USB interface is USB C (nicer than micro-USB) and with Arduino there is a reliable upload. You will need to install the CP210x USB to UART Bridge VCP Drivers from silabs.com for the USB port to be recognised on your computer. The colour ST7789V display is really nice - and although it takes up a few of the ESP32 pins, there are enough available for us to use SPI + I2S + I2S + others. NB: GPIO36 to 39 are input only. The blue power LED is (annoyingly) not programmable. The LCD backlight can be controlled as a LED on GPIO4. If you use the recommended TFT_eSPI display driver library and use a full screen-sized Sprite for the display then you can get flicker free >40FPS without effort. A LIPO battery connected to the connector underneath can be charged by the USB, and disconnecting/reconnecting either does not crash the ESP32. There is hardware battery management for charging but not for discharging, and it carries on draining until the ESP32 crashes, so, if you are powering just on an unprotected LiPo battery you may want to prevent damage to your LiPo by including some code to test the battery voltage (a simple function call) and go into deep sleep (very low power) if eg battery goes < 3.2V. I have designed a good 3D printable case available free here: https://www.thingiverse.com/thing:4501444 Have fun! PJMI

Works great. Should be noted that screen resolution is 320x240

Works great. Should be noted that screen resolution is 320x240

Works great. Should be noted that screen resolution is 320x240

Gayet güzel. Usb den yeterli akım çekebilmesi için Type-C girişi var buna dikkat edin. Lipo batarya bağlantı soketi ve kablosu da var. Açılışta logo çıkıyor sonrasında üç ana renk olan kırmızı yeşil maviye geçiş yaparak lcd ekranı test etmiş oluyor. Test bittikten sonra soldaki düğmeye basarsanız Wifi taraması yapıyor. Sağdaki de uyku konumuna alıyor.

Gayet güzel. Usb den yeterli akım çekebilmesi için Type-C girişi var buna dikkat edin. Lipo batarya bağlantı soketi ve kablosu da var. Açılışta logo çıkıyor sonrasında üç ana renk olan kırmızı yeşil maviye geçiş yaparak lcd ekranı test etmiş oluyor. Test bittikten sonra soldaki düğmeye basarsanız Wifi taraması yapıyor. Sağdaki de uyku konumuna alıyor.

Gayet güzel. Usb den yeterli akım çekebilmesi için Type-C girişi var buna dikkat edin. Lipo batarya bağlantı soketi ve kablosu da var. Açılışta logo çıkıyor sonrasında üç ana renk olan kırmızı yeşil maviye geçiş yaparak lcd ekranı test etmiş oluyor. Test bittikten sonra soldaki düğmeye basarsanız Wifi taraması yapıyor. Sağdaki de uyku konumuna alıyor.

Nice little board with good bright and clear display, included battery connection and charge management make portable devices a breeze. Referenced libraries are easy to use and all the standard ESP32 stuff works well too. Unsoldered headers also good for fitting into small 3d printed cases. Great for all sorts of things like IoT linked displays and control modules.

Nice little board with good bright and clear display, included battery connection and charge management make portable devices a breeze. Referenced libraries are easy to use and all the standard ESP32 stuff works well too. Unsoldered headers also good for fitting into small 3d printed cases. Great for all sorts of things like IoT linked displays and control modules.

Nice little board with good bright and clear display, included battery connection and charge management make portable devices a breeze. Referenced libraries are easy to use and all the standard ESP32 stuff works well too. Unsoldered headers also good for fitting into small 3d printed cases. Great for all sorts of things like IoT linked displays and control modules.

Kiváló minőségű tábla fekete bevonatú NYÁK, USB-C dugó egy nagy plusz. Jól elhelyezett elrendezés, működik a dobozból egy egyszerű demó app villogott. TIPP: ne távolítsa el a védőfóliát a kijelzőről sietve, tegye meg a kitörési csapok forrasztása után! Ez a harmadik Lilygo TTGO táblám. Mindegyik jól működik. Ezt két hét alatt szállították. Csak a Fájdalompont: docs és az online repo lehet egy kicsit kiterjedtebb, de a Szerző a GitHub érzékeny, így nem kell aggódni. Tartsuk szem előtt, hogy a képernyő 1 SPI interfészt használ, így egy kis olvasásra van szüksége, mielőtt egy másik SPI gizmot csatlakoztatna.

High quality board with black coated PCB, USB-C plug is a big plus. Well placed layout, works out of the box with a simple demo app flashed. TIP: don't remove the protective film from display in a rush, do it AFTER soldering the breakout pins! This is my 3rd Lilygo TTGO board. Every one works great. This one shipped in just 2 weeks. Only Painpoint: docs and the online repo could be a bit more extensive, but the Author on GitHub is responsive so no worries. Keep in mind that the screen uses 1 SPI interface so you need a bit of a reading before connecting another SPI gizmo.

Kiváló minőségű tábla fekete bevonatú NYÁK, USB-C dugó egy nagy plusz. Jól elhelyezett elrendezés, működik a dobozból egy egyszerű demó app villogott. TIPP: ne távolítsa el a védőfóliát a kijelzőről sietve, tegye meg a kitörési csapok forrasztása után! Ez a harmadik Lilygo TTGO táblám. Mindegyik jól működik. Ezt két hét alatt szállították. Csak a Fájdalompont: docs és az online repo lehet egy kicsit kiterjedtebb, de a Szerző a GitHub érzékeny, így nem kell aggódni. Tartsuk szem előtt, hogy a képernyő 1 SPI interfészt használ, így egy kis olvasásra van szüksége, mielőtt egy másik SPI gizmot csatlakoztatna.

Az eszköz nagy, könnyen használható a példák rendben vannak, és elég adat az interneten a legtöbb funkció programozásához. az egyetlen hiba, amit találtam, a töltő áramkör, csatlakoztatott egy 150mah akkumulátort, és néhány óra múlva elkezdett duzzadni. Szerencsére kinyitottam a készüléket ellenőrzésre, mielőtt az akkumulátor lángra kapott

Device is great, easy to use the examples are ok and enough data on the web to program most of the features. only flaw I have found is the charging circuit, connected a 150mah battery and after several hours it started swelling. luckily i opend the device for inspection before the battery burst in flames. please check

Az eszköz nagy, könnyen használható a példák rendben vannak, és elég adat az interneten a legtöbb funkció programozásához. az egyetlen hiba, amit találtam, a töltő áramkör, csatlakoztatott egy 150mah akkumulátort, és néhány óra múlva elkezdett duzzadni. Szerencsére kinyitottam a készüléket ellenőrzésre, mielőtt az akkumulátor lángra kapott

Nagy és erős kis ESP32 tábla. A TFT programozása egyszerű az Arduino grafikus felülettel és a TFT_eSPI könyvtárral. Fedélzeti wifi, vaku, Lipo-csatlakozó és 2 gombok szinte a dobozon kívül, mint IoT eszköz érzékelők, autóipari és intelligens otthon kijelzők. Most rendeltem még kettőt az okosotthonok fotovoltaikus kijelzőmhöz...

Great and powerful little ESP32 board. TFT programming is easy with Arduino GUI and TFT_eSPI library. With onboard wifi, flash, Lipo-connector and 2 buttons its nearly out-of-the-box as IoT device for sensors, automotive and smarthome displays. I just ordered another 2 for my smarthomes photovoltaic power display...

Nagy és erős kis ESP32 tábla. A TFT programozása egyszerű az Arduino grafikus felülettel és a TFT_eSPI könyvtárral. Fedélzeti wifi, vaku, Lipo-csatlakozó és 2 gombok szinte a dobozon kívül, mint IoT eszköz érzékelők, autóipari és intelligens otthon kijelzők. Most rendeltem még kettőt az okosotthonok fotovoltaikus kijelzőmhöz...

Great product, you can check my tutorials for these boards https://www.youtube.com/channel/UCit2rVgOvhyuAD-VH5H_IHg

Great product, you can check my tutorials for these boards https://www.youtube.com/channel/UCit2rVgOvhyuAD-VH5H_IHg

Great product, you can check my tutorials for these boards https://www.youtube.com/channel/UCit2rVgOvhyuAD-VH5H_IHg

Az ESP32 modul tökéletes az IoT alkalmazásaihoz, vagy tanuláshoz! Tökéletesen működik, ideális időjárási állomások és watt méter. Dokumentáció nagyon könnyű megtalálni.

Module ESP32 parfait pour les applications IoT's, ou l'apprentissage ! Fonctionne parfaitement, idéal pour les stations météo et pour les watt mètres. Documentation très facile à trouver.

Az ESP32 modul tökéletes az IoT alkalmazásaihoz, vagy tanuláshoz! Tökéletesen működik, ideális időjárási állomások és watt méter. Dokumentáció nagyon könnyű megtalálni.

das läuft prima

das läuft prima

das läuft prima