SorinB
Q: When will Ender 3 Pro version be available?
Kérdezte NiPaH tovább 2023-01-17 04:55:41
Q: Can I attach this on a black and decker drill?
Kérdezte dijolthomas tovább 2019-06-02 08:08:55
SorinB Thisis designed to be used with rotary tools compatible with Dremel, not with drills
2022-09-25 03:26:35 Hasznos (0)Q: What type for ender3 and ender 3pro
Kérdezte creatron tovább 2022-09-25 01:10:30
SorinB TypeB is the one for Ender 3 and Pro
2022-09-25 03:25:11 Hasznos (0)Q: can you use this on ender 5?
Kérdezte Boske tovább 2022-09-07 03:32:04
SorinB No as it is, because the attachments for the belts are different.
2022-09-08 02:28:40 Hasznos (0)
SorinB I don't think so, because the mounting plate is different (the belt slots are in lower position for Ender 3). If you can manage that, anything else should work.
2022-05-10 02:33:52 Hasznos (0)Q: Is this an official Creality upgrade kit?
Kérdezte Tom S tovább 2022-04-21 04:29:33
SorinB Yes, this is the real deal.
2022-04-22 09:17:32 Hasznos (0)
SorinB Yes, but the kit contains all three brackets, so do not worry about that.
2022-03-09 03:44:15 Hasznos (1)Q: what is the maximum temperature we can use on this
Kérdezte BG538161619 tovább 2022-02-21 04:20:49
SorinB The extruder is not fully metal, it has bowden tube inside, so the max temperature should not exceed 260 degrees centigrade.
2022-02-21 06:18:50 Hasznos (0)
SorinB The voltage should be 24, not 1,4. Check where which end of the cable is going. The motor ends have two cables inverted and the one that connect with the original cable do not have that.
2022-02-09 03:17:24 Hasznos (0)
SorinB For E-Steps, you can leave them unchanged, since the stepper motor is identical on both extruders. For precise calibration, there can be some small differences between the two stepper motors, so you can run the extruder calibration routine. About replacing, only two steps: 1- remove the old gear; 2- install the new one.
2022-01-27 09:27:38 Hasznos (0)Q: does it fit on alfawise u30pro?
Kérdezte davcbr tovább 2020-09-13 03:28:04
SorinB Yes,it may fit if the belt fits. The V-slot wheels are at the same distance and the wires are long enough, no worry about that.
2022-01-17 05:16:17 Hasznos (0)Q: would this work for a cr10s pro?
Kérdezte Paulloth21 tovább 2020-03-27 07:26:21
SorinB Itworks wit any printer that accept auto bed leveling sensor (that have the dedicated pins on the mainboard or near the print head), with the appropriate firmware.
2022-01-17 05:05:19 Hasznos (0)Q: can be used for tig welding?
Kérdezte joeclone tovább 2018-08-13 01:47:46
SorinB Youdon't need TIG, the rods are intended for use with a blowtorch. But, yes, i think you can.
2022-01-17 05:02:06 Hasznos (0)
Q: Is this compatible with Ender 3 Max?
Kérdezte BG364754465 tovább 2022-01-11 07:18:36
SorinB No, because the threaded rod is shorter. Everything else should be OK.
2022-01-11 08:53:14 Hasznos (0)Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
.jpg)
SorinB It is already available. Read the full name of the item. All three mounting adaptors are included.
2023-01-18 02:37:10 Hasznos (0)