ucfnf
Q: can I bind this to my jumper t18?if so whats the protocol?
Kérdezte MRFLYHIGH tovább 2021-04-08 08:55:13
Q: what is the flying control range?
Kérdezte BG173625121 tovább 2020-11-22 05:43:54
ucfnf The receiver is a RadioLink R8FM. RadioLink says, the control distance is 2000 meters in the air.
2021-03-08 12:44:31 Hasznos (1)Q: What's the recommended batt for the hook extra 300-h
Kérdezte BG505034171 tovább 2021-03-02 07:34:31
ucfnf User manual recommand 4S Li-Po Battery 14,8 V 1500 -2200 mAh.
2021-03-03 12:41:17 Hasznos (1)Q: Is there a throttle pinout on this board to use a brushless ESC?
Kérdezte cvflyer tovább 2021-02-16 08:29:30
ucfnf Sorry no, there are only 2 pinouts to connect and throttle a brushed motor.
2021-02-16 01:20:33 Hasznos (0)Q: Can be bind with Jumper T12 ?
Kérdezte popad tovább 2021-02-06 10:41:17
ucfnf You need the Volantex protocol " V 761". If it´s not supported, try to load it from multi-module.org
2021-02-08 04:58:51 Hasznos (0)Q: where can i find more references / study about this?
Kérdezte freecarve tovább 2021-01-30 02:30:40
ucfnf I think it´s comparable with the Fisher Wallace stimulator, see fisherwallace.com and their product reviews for more information.
2021-01-31 11:59:37 Hasznos (0)Q: Do I need to have 2 antennas attached? Can I run it with only 1 antenna?
Kérdezte Tomas tovább 2021-01-13 05:53:53
ucfnf Yes, it will run with only 1 antenna, I tested it. There is only one receiver inside, which switch to the antenna with the best signal.
2021-01-15 09:49:26 Hasznos (0)Q: Is the Razor compatible with a Radiomaster TX16S?
Kérdezte Gilles tovább 2021-01-07 10:08:23
ucfnf Yes, use the protocol RadLink Air and push the tiny binding switch of the receiver.
2021-01-11 01:01:15 Hasznos (0)Q: what transmitters works with the receiver in the RTF
Kérdezte BG441854224 tovább 2020-09-23 01:21:04
ucfnf The included TX is a RadioLink TX with eachine label. The receiver works also with each TX with Open TX Multi protocol. The protocol is: RadLink Air. The receiver is hidden under the FC. Pull out and push the tiny binding switch for binding.
2021-01-04 09:51:17 Hasznos (1)Q: Which protocol is used by the included RX / Tx?
Kérdezte kieber tovább 2020-11-20 10:37:49
ucfnf Works with OpenTx Multi protocol, latest update:" RadLink Air ". You must pull out the receiver -its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-01-04 09:31:55 Hasznos (0)Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ucfnf It´s a RadioLink receiver and it works with OpenTx Multi protocol, latest update: "RadLinkAir". You must pull out the receiver-its under the FC- to push the tiny binding switch. Don´t forget the Fine Tuning.
2021-04-15 08:15:23 Hasznos (0)