losip
Q: At what cell Voltage does this cut off the power? Will it drain my cells low?
Kérdezte Maxim tovább 2021-02-09 02:21:51
losip Cuts off at cell voltage (all in parallel) of 3.1v. For best battery life I wold have preferred it to be 3.2v but it is acceptable at 3.1v
2021-09-27 05:47:53 Hasznos (0)
losip Any type of 18650 lithium battery but they should all have the same capacity
2021-09-27 05:45:09 Hasznos (0)
The seller yes,it just an air blower
2021-09-13 06:57:46 Hasznos (0)Q: does it work with xiaomi home or with the gateway for imilab ec2 camera?
Kérdezte BG155503633 tovább 2021-08-10 12:38:58
losip I'm using it with the Xiaomi gateway and monitoring it from Xiaomi Home app. Since ImiLab is part of the Xiaomi eco-system, it is quite possible that it would work but personally I think it's unlikely because ImiLab is camera-centric even though it also uses the same Home app.
2021-08-10 12:48:25 Hasznos (0)
losip No, it's just a pump. Apply power and it runs, remove power and it stops. There's no pressure or flow sensor built in
2021-08-04 02:01:44 Hasznos (0)Q: the pump is activated automatically when a water tap is opened?
Kérdezte BG542354756 tovább 2021-03-03 08:40:37
losip No, it\'s just a pump. Apply power and it runs, remove power and it stops. There's no pressure control built in.
2021-08-04 02:01:03 Hasznos (1)Q: CAN THIS BE CONTROLED BY TEMPERATURE AS I CANT SEE ANY INDICATION OF THAT
Kérdezte adrian tovább 2021-08-01 05:25:41
losip No, it's just a pump. Apply power and it runs, remove power and it stops. You need to use an external (tank) thermostat to have it controlled by temperature
2021-08-04 01:58:27 Hasznos (0)Q: What is the max battery Voltage?
Kérdezte pantelist06 tovább 2021-05-24 11:41:05
losip 4.5v
2021-05-24 11:48:34 Hasznos (1)
losip Mine has the Xiaomi Mijia logo on the accessories box and on the base of the drill
2021-05-04 04:33:59 Hasznos (0)
losip You can use any device that is supported by the Zigbee alliance. Go to zigbeealliance{dot}org and search for the compatibility list
2021-04-01 02:28:43 Hasznos (0)Q: 1) This item must work in pair? 2) Can hdmi-ethernet converter be used with this item?
Kérdezte Shopping Time tovább 2021-02-24 07:28:54
losip There's a clear picture showing the correct configuration is only when working as a pair. It multiplexes two connections onto one Cat 5 cable but must then split them again for use
2021-03-21 01:56:57 Hasznos (0)Q: How to set the settings of lead acid in this meter
Kérdezte Tanishq Gaharwar tovább 2019-03-13 05:41:18
losip Unplug from power, hold down the button on the back and apply power again. You will be in Settings mode. Set the P number to be equal to number of cells in your lead acid battery using the front and back buttons. Then power cycle again
2021-03-17 07:27:59 Hasznos (1)Q: Can you please tell us how to reset the voltmeter so that i can use it on a different battery pack?
Kérdezte Kishore Yadav tovább 2018-07-26 02:38:26
losip Unplug from the battery, hold down the button on the back and power up again. You will be in the settings menu. After getting the settings as you want them for the new battery, cycle the power again
2021-03-17 07:25:05 Hasznos (0)
losip As Rone says, if you power up and then push buttons, nothing happens. Unplug it, hold down the button on the back and plug in again. You will be in settings mode and can change parameters according to instructions. When choosing the number of cells, the button on the back decreases the count and the one on the front increases it. Choose the value you want, then unplug and replug. The settings will be remembered. takes a little fiddling but remember to power cycle to get into settings mode while holding down the button.
2021-03-17 07:20:34 Hasznos (3)
losip All batteries in parallel. As many as you like.
2020-12-13 02:39:33 Hasznos (0)Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
losip The knurled knob at the handle end has three positions: to the right, the screwdriver will rotate clockwise; to the left, anti-clockwise and in the centre, pressing the trigger does nothing,
2021-11-28 09:33:21 Hasznos (0)