MihaiP
Q: The current is indicated correctly up to 0.001 A , compared to a good multi-meter ?
Kérdezte MihaiP tovább 2019-09-05 01:05:12
Q: i don't see any IR led on this, how is the nght vision? ;
Kérdezte theGeezer tovább 2022-03-01 08:02:23
MihaiP Not visible on the image, but the IR works fine, as indicated in the documentation.
2022-03-01 08:37:12 Hasznos (0)Q: What is the speed of the linear actuator?
Kérdezte BG441812575 tovább 2021-11-27 04:41:03
MihaiP Depends on the stepper motor driver. Count on several seconds per 100 mm, as fastest move. The lowest is as slow as you want!
2021-11-27 05:48:38 Hasznos (0)Q: Does the SD card on this module work on the Arduino Mega ?
Kérdezte BG154735114 tovább 2021-10-22 11:45:17
MihaiP Surely ! You can watch pictures from SD on the display, with appropriate Arduino library.
2021-10-23 02:12:20 Hasznos (0)
MihaiP Look in grabcad.com library slide-axis-table-1#!
2021-09-09 12:49:24 Hasznos (0)
MihaiP Not recommended. Notebook manufacturers require to use only their adapters, since most of them are not just AC-DC converters.
2021-06-15 08:27:17 Hasznos (0)Q: can this play files streaming on the internet with suitable connection to wifi with arduino?
Kérdezte BG422441011 tovább 2021-05-06 06:32:10
MihaiP No, it reads the sound files from SD only. There are other boards for what you need.
2021-05-07 12:47:05 Hasznos (0)
MihaiP According to product information: "The backlight is always on, cannot control the backlight: backlight is connect to 3.3V"
2021-04-18 02:35:45 Hasznos (0)
MihaiP Zero volts is wrong! Possible causes: Power it at 3.3V only! Use analog read but in a 3.3V board! My readout: about 620 (2 V in air) and 310 (1V) in water. You must calibrate yours.
2021-02-02 07:50:44 Hasznos (0)
MihaiP Check the switches of the board. Set it to Mega and test it in Arduino. Works fine. Then try WiFi alone. All together is for advanced users.
2020-12-31 11:18:47 Hasznos (1)Q: it says adjustable. how to adjust?
Kérdezte BG101554944 tovább 2020-12-12 06:51:01
MihaiP You can adjust with the small trimmer: any output voltage between 0 and about 1.5 V below the input voltage.
2020-12-13 01:43:17 Hasznos (0)Q: does it have accelerometer on board?
Kérdezte katseros tovább 2020-12-02 04:37:23
MihaiP No
2020-12-02 01:18:42 Hasznos (0)Q: There is no dimension for mounting surface to mounting surface. Can you provide?
Kérdezte BG419535339 tovább 2020-09-23 11:29:33
MihaiP Platform 45x40mm. Distance between out-most channels: 30mm.
2020-09-29 01:06:40 Hasznos (0)Q: Can a IC chip span the gap the same as the standard plastic breadboard?
Kérdezte BG435423340 tovább 2020-08-03 12:22:30
MihaiP Yes, the spacing over the gap is perfect for IC chips.
2020-08-03 02:12:21 Hasznos (1)
MihaiP The box must remain of reasonable size. It covers several lengths, enough in most cases.
2020-07-21 12:29:41 Hasznos (0)
Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
BENHAMMOU yes
2022-04-20 11:31:29 Hasznos (0)