bektorkhan
Q: Warning this is a Low side version only, common ground and Supply voltage up to 26V
Kérdezte bektorkhan tovább 2024-04-02 06:27:27
Q: bonjour witch contrôler Can I use with this motor ? thank you.
Kérdezte BG161215159 tovább 2024-01-31 02:14:48
bektorkhan Voltage 6-20S means 24-80 V ruffly, use as high as possible for efficiency
2024-02-21 06:49:18 Hasznos (1)Q: How is it connected? Is any sensors included?
Kérdezte bektorkhan tovább 2020-09-05 02:42:47
BG111141435 mine didn't come with any sensors
2022-03-09 05:22:54 Hasznos (0)
bektorkhan Typing Error 20V should as an estimate be 26V. And yes it will work for you, but if I were you I would choose a bigger PSU, it is not wise to run above 80% power, if you want it to last for years!
2020-08-31 01:28:04 Hasznos (0)
Q: What are the 4 pins on the side of the board for? Vcc, Gnd and the other two?
Kérdezte ebolisa tovább 2019-10-05 05:29:44
bektorkhan USB+ and USB- since M18 should have an USB interface, USB sound card I believe.
2020-02-27 07:01:18 Hasznos (0)Q: Does the switch need a neutral wire connection?
Kérdezte Rainer Hoogendijk tovább 2019-01-12 09:50:42
bektorkhan Yes it needs Neutral, 3 connections L , N , L1=fan
2019-10-09 10:11:30 Hasznos (0)Q: What is the range of input voltage from the solar panel?
Kérdezte letec tovább 2018-11-08 12:11:46
bektorkhan Max PV Voltage is 50V
2019-09-13 06:07:02 Hasznos (2)
yikkkk Sorry it can't do this.
2019-04-30 03:56:53 Hasznos (0)Q: will it fit in a 2 inch electrical box ?
Kérdezte memilas tovább 2018-08-08 02:14:56
bektorkhan CC the mounting holes is 58mm ish, so 2.3 inch so I think it would fit!
2019-01-16 06:44:03 Hasznos (0)Q: Which app do we use to control switch? Is app compatible to sonoff switches?
Kérdezte Fasirelas tovább 2018-08-18 04:24:49
bektorkhan eWeLink is the same app as SonOff uses, so they should work.
2019-01-16 06:37:40 Hasznos (0)Q: Will it work on a WIFI that doesn't have Internet Connection?
Kérdezte Kezzy tovább 2018-02-10 01:27:09
bektorkhan Not as is, you need to flash Tasmota or similar Firmware. Not for everone can do that!
2019-01-16 06:22:37 Hasznos (0)Q: Does this switch require N/Neutral wire in the switch box?
Kérdezte LucasBoy tovább 2018-09-20 09:28:37
bektorkhan Ýes it reqiures N/Neutral, don't work without it!
2019-01-16 06:20:19 Hasznos (0)Q: Can I use 3 of these to balance a 12S battery?
Kérdezte i.am.neffson tovább 2018-05-08 06:18:26
bektorkhan I don't see why not , could also be used for 2S and 3S. Each circuit is loading the cell with 42 ohm (100mA) if the cell voltage higher than 4.2 Volt. For 2S ex. do not connect the third and fourth cell!
2019-01-03 03:45:58 Hasznos (0)Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
lmml GOOD
2024-04-02 09:00:03 Hasznos (0)