cmeng48
Q: can i use to regulate the speed of a dc motor?
Kérdezte BG375415825 tovább 2022-05-28 07:37:16
cmeng48 As long as your motor is less than 2000 watt.. it should work but talk to your electrician for proper advice. Personally this is an open item and could be dangerous if not housed properly.
2022-05-28 06:15:25 Hasznos (0)
BG549021181 I think it should be Stainless Steel
2021-03-02 09:43:10 Hasznos (8)Q: Does this kit fit the rear master cylinder of a 2005 harley 883?
Kérdezte Lucio tovább 2021-03-24 05:58:28
cmeng48 No.
2021-10-13 07:42:06 Hasznos (0)Q: hi! is this item can be use for electric drill?
Kérdezte zack tovább 2020-09-23 03:24:37
cmeng48 no.
2021-10-13 07:41:48 Hasznos (0)Q: Can it be used on mild steel?
Kérdezte viking61 tovább 2021-10-12 08:30:37
cmeng48 Hi viking61, I am a machinist long time ..No it cannot be used on mild steel they are dissimilar metals. For mild steel use silver brazing rod with at least 40% silver and a brazing flux for a strong joint or repair. Hope this helps.
2021-10-12 08:38:50 Hasznos (1)Q: Is the Dremel 3000 compatible?
Kérdezte weyselkalkan tovább 2021-07-09 05:19:28
cmeng48 What do you mean?.. if you are asking if the dremel tool is to be used as a tool for gear cutting then no! Gear cutting requires a lot of experience in machining and a lot of machine tools. I hope this helps.
2021-07-09 05:43:29 Hasznos (1)Q: Is it solar energy dependent? will it work at night?
Kérdezte GKM tovább 2019-12-20 01:59:28
cmeng48 Itshould work at night but not sure cause I don't weld at night.
2021-05-15 01:01:07 Hasznos (0)Q: When would a Module 1 PA20 Bore 22mm "5" HSS Involute Gear Milling Cutter be available. thanks.
Kérdezte BG445191415 tovább 2021-05-14 08:25:34
cmeng48 Iam only a buyer..so I don't know. Try Aliexpress.com if you are in a hurry.
2021-05-15 12:59:55 Hasznos (0)
cmeng48 yesready to cut.
2021-05-15 12:58:40 Hasznos (0)Q: Can i use this in my guitar as a killswitch? is it normally opened or normally closed one?
Kérdezte Arkonil tovább 2019-08-26 06:19:28
cmeng48 Nodon't think so!
2021-05-05 06:15:19 Hasznos (0)
cmeng48 Thickness is 1.6mm 1-16'' of an inch.. Length of rod is 500mm or about 20 inches. They have flux in between rod so you don't have to use flux.
2021-03-20 05:49:04 Hasznos (0)
Q: does this phone have 802.11ac wifi. as it says in the description.
Kérdezte BG364611155 tovább 2021-02-27 11:15:21
cmeng48 Sure does!
2021-02-28 02:08:33 Hasznos (2)Q: good for Al an copper combined?
Kérdezte Cusniriuc tovább 2020-02-22 03:20:02
cmeng48 No.
2021-02-18 04:44:31 Hasznos (0)Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
cmeng48 Yesit can be used for aluminum..all carbide end mills can.
2022-08-12 09:34:38 Hasznos (0)