RAZZORR55
Q: can this be compatible to some cheap Fpv goggles?thanks
Kérdezte BG535316151 tovább 2021-10-31 09:11:39
RAZZORR55 Hi, yes it can be used with most FPV Goggles and fpv receivers ,its got forty channels to choose from,cheers.
2021-10-31 11:45:54 Hasznos (0)
RAZZORR55 Placeon a AUX switch toggle type up front cam on down rear cam on ,cam one is always on in up position say your front cam its the priority cam .
2021-04-18 02:44:31 Hasznos (0)Q: hi, is motor mount included in this kit version?
Kérdezte qubert555 tovább 2021-03-24 04:31:53
RAZZORR55 HI, yes a full parts pack is included ,for motor mount ,wings, batt tray etc, nice kit for money.
2021-03-25 03:24:46 Hasznos (0)Q: Which receiver is the best for this system?
Kérdezte Kbmahe tovább 2021-02-18 10:35:10
RAZZORR55 HiTESTED MINE ON PWM on a flip switch works perfect one cam on all time then flip switch for other cam ,cheers.
2021-02-19 02:25:06 Hasznos (1)
RAZZORR55 Hi, Jack The answer to all is no it can't ,as it as an in built diode protection to stop any voltage return and spikes as these would just blow the circuit, its a nice unit for what its intended PWM Motor control. If your worried just put a HV shunt diode in line and a suitable capacitator ACROSS MOTOR TERMINALS, hope this helps.
2021-02-11 03:12:12 Hasznos (1)Q: why won’t his bind with xjt lite module?
Kérdezte joel tempongko tovább 2020-12-24 11:37:25
RAZZORR55 The DJT XLITE is running the new access protocol but should run both were as the receiver is in ACCST D8 mode. MAKE SURE THE PROTOCOL IS CHANGED IN RADIO. 1.Connect the FC and go to CLI. 2.Write the bind command: For Betaflight 4.x bind_rx_spi For Betaflight 3.x frsky_bind 3. Activate the bind function on the radio. 4. Go to the CLI and write Save 5. Stop the bind function on the radio 6. Reboot the FC
2020-12-24 03:14:56 Hasznos (0)
RAZZORR55 Minecame with the circuit printed on a separate paper ,but if you use the silk screen on the board it basically tells you what goes s were.
2020-12-05 02:36:04 Hasznos (1)
RAZZORR55 6.5INCH,BUT MOTOR EXTENTION KIT ALLOWS UP TO 7.5in
2020-09-18 12:24:48 Hasznos (0)
RAZZORR55 GLASS
2020-09-18 12:22:17 Hasznos (0)
Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
RAZZORR55 Hi, yes but make sure you check the wire polarity there clearly marked ,you can use most transmitters . cheers
2021-11-12 12:48:33 Hasznos (0)