Neslarc
Zeemax It will buzz constantly until you disconnect it
2020-10-20 09:41:23 Hasznos (1)
Neslarc The probe wires to the circuit board keep breaking off. I solder them back on but after a short while they break again.
Q: All my Rx are Flysky. What module do you need to add FlySky AFHDS and AFHDS2A to the TX18S/Lite?
Kérdezte Neslarc tovább 2020-09-18 06:26:08
machead Just buy the full version for USD20 extra. The A7105 module alone cost USD14. Saves you the hassle of hacking the transmitter and guaranteed to work.
2020-09-18 06:44:10 Hasznos (1)
Q: What i sthe max voltage and current for this motor?? I think i over powered them
Kérdezte Tsar Rex tovább 2019-10-03 10:08:27
Neslarc They are for 3.7V 1S lipo battery brushed ESC. I wouldn't exceed 5V. Don't know what the amp load is but it is very low. You can get 20 minutes flying on a 250 mAh 1S battery.
2019-10-04 06:10:48 Hasznos (2)Q: can I use this prop for motor mounted on the back of the plane?
Kérdezte RONAK10 tovább 2018-02-27 03:01:24
Neslarc Yes. Always mount the propeller so the numbers on the blades face towards the front of the airplane. You will have to reverse the direction of the motor rotation.
2019-08-11 08:31:17 Hasznos (0)Q: With which protocol it's works?
Kérdezte racz96 tovább 2019-06-13 04:01:44
Neslarc It uses Flysky AFHDS protocol.
2019-07-10 07:19:24 Hasznos (0)Q: is it compatible with the flysky fs-I6?
Kérdezte Adryanvdb tovább 2018-10-18 11:49:02
Neslarc Yes. It binds to Flysky FS-i6 transmitter if you switch to AFHDS protocol. You have to bind to the transmitter every time you change the battery.
2019-07-10 07:17:53 Hasznos (0)Q: What is the motor shaft diameter?
Kérdezte Neslarc tovább 2019-02-08 07:24:43
Jonnie 3.17mm
2019-02-27 08:15:40 Hasznos (2)
Őszintén meghívjuk Önt, hogy iratkozzon fel a Meghívó Válasz e-mailre!
Ha feliratkozik, e-mailben meghívjuk Önt, hogy válaszoljon az embereknek a termékekkel kapcsolatos kérdéseire. Ha feliratkozol, megkapod a "Hasznos jelvényt " is! Az adatvédelmi beállítások oldalon bármikor leiratkozhat.
Segíts másoknak, és légy boldogabb!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
BG723215041Kel55 You unplug it so then you replug it in . Then you can see the display tells you the current Voltage
2022-02-04 10:47:09 Hasznos (1)