Minden üzenet

Q: Will Banggood sell a RP-SMA version?

Kérdezte danarrib tovább 2018-11-19 08:59:29

JohnHutch they do...search

2022-07-31 10:11:32 Hasznos (0)
Beküldés
Válaszok (1)

Q: Current Sensor Scale?

Kérdezte danarrib tovább 2017-11-12 11:21:25

BG351738321 5V Best.

2022-02-08 01:02:20 Hasznos (0)
Beküldés
Válaszok (2)

Q: Does this props needs to be balanced?

Kérdezte danarrib tovább 2019-10-23 10:04:19

antomolog у меня почти идеальные

2021-10-09 12:33:16 Hasznos (0)
Beküldés
Válaszok (2)

Q: كم بطارية استطيع وضعها في كل خلية

Kérdezte abuamroamaireh tovább 2021-02-05 05:52:03

danarrib You can wire in parallel as many as you want.

2021-08-04 12:44:34 Hasznos (2)
Beküldés
Válaszok (3)

tedhancock68 When I started making packs I thought I didn’t need any balancing at all since I was using new, Japanese cells and slow charging. Now, $300 in lost batteries has convinced me to permanently install one of these on every pack. It adds 50 - 100% to the cost of a pack, but very much worth it!

2020-12-23 10:37:51 Hasznos (0)
Beküldés
Válaszok (3)

Q: How can it be programmed? Where's the Instructions Manual?

Kérdezte danarrib tovább 2020-01-24 12:29:22

BG561117159 where can I find programming instructions please?

2020-09-01 11:29:05 Hasznos (0)
Beküldés
Válaszok (1)

Q: Can you please send a picture of the back side of this board?

Kérdezte danarrib tovább 2020-11-10 07:02:28

tedhancock68 You mean is there any components, traces, or electrical conductivity on the back? If that is your question then...no. It is well insulated on the back side with some rubbery coating and conformal.

2020-12-25 03:36:17 Hasznos (2)
Beküldés
Válaszok (2)

Martin The XSR receiver inside could easily sent telemetry data to your transmitter. But I doubt most of the simulator softwares will transfer these data to the XSR.

2020-11-02 05:43:42 Hasznos (0)
Beküldés
Válaszok (2)

Q: What's the differente between T7056C and T7056C PRO version?

Kérdezte danarrib tovább 2019-11-26 02:23:58

BG114816400 The Pro version has more material on the connection point between hub and blade. The old ones were prone to explode when running 6S Low kv setups.

2020-10-29 01:48:47 Hasznos (0)
Beküldés
Válaszok (2)

Q: When the 1550kv version will be available?

Kérdezte danarrib tovább 2020-09-19 04:25:35

Hattiv Around Oct 26th

2020-10-09 06:03:22 Hasznos (1)
Beküldés
Válaszok (1)

Q: If it has a Barometer and I2C pads, would be PERFECT.

Kérdezte danarrib tovább 2020-08-08 11:28:40

BG454816422 According to the datasheet of STM32F722 LQFP64 and the HIFIONRC Betaflight unified target board definition, the MCU pins B10 and pin B11 (TX3,RX3 on solder pads) should be mappable to I2C device 2. No guarantees, but I'm going to attempt using that.Update: tried and it's working. I have a BMP280-3.3. VCC of baro is connected to the 3.3V PAD, SCL of baro is connected to TX3, SDA of baro is connected to RX3. Here are the betaflight configuration changes to make it work:resource SERIAL_TX 3 NONEresource SERIAL_RX 3 NONEresource I2C_SCL 2 B10resource I2C_SDA 2 B11set baro_bustype = I2Cset baro_i2c_device = 2set baro_i2c_address = 0set baro_hardware = AUTO

2020-10-06 05:30:11 Hasznos (2)
Beküldés
Válaszok (2)